Control of liquid bridging induced stiction of micromechanical structures

Stiction, the unwanted adhesion of micromachined components to the underlying substrate, is a vexing problem encountered during the fabrication of microelectromechanical systems. Liquid bridging of rinse liquids after release etch processing introduces significant surface tension forces which can initiate stiction. We show that liquid bridging can be substantially eliminated by appropriate design of the microstructure periphery. Antistiction tabs located at the center of doubly clamped beams, or at the ends of cantilevered beams, are shown to improve release yield significantly in both surface and bulk micromachining processes.

[1]  H. Fujita,et al.  Photoresist-Assisted Release of Movable Microstructures , 1993 .

[2]  M. Orpana,et al.  Control of residual stress of polysilicon thin films by heavy doping in surface micromachining , 1991, TRANSDUCERS '91: 1991 International Conference on Solid-State Sensors and Actuators. Digest of Technical Papers.

[3]  W. Messner,et al.  Effective methods to prevent stiction during post-release-etch processing , 1995, Proceedings IEEE Micro Electro Mechanical Systems. 1995.

[4]  Roger T. Howe,et al.  The effect of release-etch processing on surface microstructure stiction , 1992, Technical Digest IEEE Solid-State Sensor and Actuator Workshop.

[5]  T. Christenson,et al.  Fabrication of micromechanical devices from polysilicon films with smooth surfaces , 1989 .

[6]  R. Howe,et al.  Thermal assembly of polysilicon microstructures , 1991, [1991] Proceedings. IEEE Micro Electro Mechanical Systems.

[7]  K. Yoshimi,et al.  YAG laser assisted etching for releasing silicon micro structure , 1993, [1993] Proceedings IEEE Micro Electro Mechanical Systems.

[8]  H. Tilmans,et al.  Stiction of surface micromachined structures after rinsing and drying: model and investigation of adhesion mechanisms , 1994 .

[9]  J. A. Voorthuyzen,et al.  Investigation of attractive forces between PECVD silicon nitride microstructures and an oxidized silicon substrate , 1992 .

[10]  W. Messner,et al.  Effects of elevated temperature treatments in microstructure release procedures , 1995 .

[11]  C. Hsu,et al.  Mechanical stability and adhesion of microstructures under capillary forces. II. Experiments , 1993 .

[12]  William C. Tang,et al.  Laterally driven polysilicon resonant microstructures , 1989, IEEE Micro Electro Mechanical Systems, , Proceedings, 'An Investigation of Micro Structures, Sensors, Actuators, Machines and Robots'.

[13]  A. Adamson.  Physical chemistry of surfaces , 1960 .

[14]  C. Hsu,et al.  Mechanical stability and adhesion of microstructures under capillary forces. I. Basic theory , 1993 .

[15]  C. Mastrangelo,et al.  A dry-release method based on polymer columns for microstructure fabrication , 1993, [1993] Proceedings IEEE Micro Electro Mechanical Systems.

[16]  H. Fujita,et al.  Electrostatic parallelogram actuators , 1991, TRANSDUCERS '91: 1991 International Conference on Solid-State Sensors and Actuators. Digest of Technical Papers.

[17]  Albert P. Pisano,et al.  Polysilicon microgripper , 1990, IEEE 4th Technical Digest on Solid-State Sensor and Actuator Workshop.

[18]  T. Abe,et al.  Low strain sputtered polysilicon for micromechanical structures , 1996, Proceedings of Ninth International Workshop on Micro Electromechanical Systems.