WR-3 Band Waveguides and Filters Fabricated Using SU8 Photoresist Micromachining Technology

This paper demonstrates a two-layer SU8 photoresist micromachining technology that has similar performance to conventionally machined metal. The technology is demonstrated in the WR-3 band (220-325 GHz). Three different WR-3 band circuits, namely a WR-3 band straight through waveguide, a bandpass filter and a dual-band filter are demonstrated. For the measurements, a conventionally precision machined metal block was used for the WR-3 band waveguide and the bandpass filter to achieve good calibration and accurate interconnection with standard waveguide flanges; whereas, for the dual-band filter, two back-to-back right-angle bends are added in order to achieve accurate, reliable waveguide interconnection without using the metal block. A measured average insertion loss of 0.03 dB/mm has been achieved for the 14.97 mm long straight through waveguide. This is comparable to the loss of around 0.02 dB/mm for a standard metal waveguide at this frequency. The fifth-order waveguide filter exhibits an 8% 3 dB bandwidth at a central frequency of around 300 GHz. The minimum passband insertion loss was measured to be around 1 dB and the return loss was better than 10 dB throughout the passband. The filter results showed a notable improvement over those obtained from the separate SU8 layer technique that was also used to make the same devices for comparison. To further demonstrate the advantages of the new two-layer SU8 micromachining technique, the dual-band filter included isolated regions in the waveguide channels that would have not been possible for micromachining using the previous separate single layer technique. The performance of the micromachined dual band filter was excellent in terms of very low insertion losses on both passbands.

[1]  Steve Arscott,et al.  Integrated microfluidics based on multi-layered SU-8 for mass spectrometry analysis , 2004 .

[2]  Norihiko Sekine,et al.  At the Dawn of a New Era in Terahertz Technology , 2007, Proceedings of the IEEE.

[3]  Yi Wang,et al.  Measurements of micromachined submillimeter waveguide circuits , 2010, 2010 76th ARFTG Microwave Measurement Conference.

[4]  Alain Maestrini,et al.  A Broadband 900-GHz Silicon Micromachined Two-Anode Frequency Tripler , 2011, IEEE Transactions on Microwave Theory and Techniques.

[5]  David Paul Steenson,et al.  Measurements to 320 GHz of millimetre-wave waveguide components made by high precision and economic micro-machining techniques , 2003, 2003 High Frequency Postgraduate Student Colloquium (Cat. No.03TH8707).

[6]  Yi Wang,et al.  Design of multiple-passband filters using coupling matrix optimisation , 2012 .

[7]  Gabriel M. Rebeiz,et al.  Low loss micromachined filters for millimeter-wave telecommunication systems , 1998, 1998 IEEE MTT-S International Microwave Symposium Digest (Cat. No.98CH36192).

[8]  Jens Bornemann,et al.  Inline TM/sub 110/-mode filters with high-design flexibility by utilizing bypass couplings of nonresonating TE/sub 10/01/ modes , 2003 .

[9]  M.V. Lukic,et al.  Modeling of 3-D Surface Roughness Effects With Application to $\mu$-Coaxial Lines , 2007, IEEE Transactions on Microwave Theory and Techniques.

[10]  J. Papapolymerou,et al.  Silicon Micromachined W-Band Folded and Straight Waveguides Using DRIE Technique , 2006, 2006 IEEE MTT-S International Microwave Symposium Digest.

[11]  M. Despont,et al.  SU-8: a low-cost negative resist for MEMS , 1997 .

[12]  K. Sarabandi,et al.  Micromachined J-band rectangular waveguide filter , 2011, 2011 XXXth URSI General Assembly and Scientific Symposium.

[13]  Yi Wang,et al.  Micromachined W-band waveguide and filter with two embedded H-plane bends , 2011 .

[14]  M. Lancaster,et al.  Micromachined WR-3 waveguide filter with embedded bends , 2011 .

[15]  N. S. Barker,et al.  Fabrication and Integration of Micromachined Submillimeter-Wave Circuits , 2011, IEEE Microwave and Wireless Components Letters.

[16]  Jian Chen,et al.  Micromachined 300-GHz SU-8-Based Slotted Waveguide Antenna , 2011, IEEE Antennas and Wireless Propagation Letters.

[17]  N. S. Barker,et al.  SU-8 micromachining of millimeter and submillimeter waveguide circuits , 2009, 2009 IEEE MTT-S International Microwave Symposium Digest.

[18]  A. Mata,et al.  Fabrication of multi-layer SU-8 microstructures , 2006 .

[19]  N. Scott Barker,et al.  Development of a Multi-layer SU-8 Process for Terahertz Frequency Waveguide Blocks , 2005, IEEE MTT-S International Microwave Symposium Digest, 2005..

[20]  Ying-Tung Chen,et al.  Precision fabrication of an arrayed micro metal probe by the laser-LIGA process , 2005 .

[21]  Wanjun Wang,et al.  Study on the postbaking process and the effects on UV lithography of high aspect ratio SU-8 microstructures , 2004 .

[22]  Charles H. Smith,et al.  Integrating micromachined circuits to submillimeter systems , 2010, The 40th European Microwave Conference.

[23]  Jia-Sheng Hong,et al.  Microstrip filters for RF/microwave applications , 2001 .

[25]  G. Craven,et al.  Evanescent Mode Microwave Components , 1987 .