Damage performance in drilling of carbon fiber-reinforced polyetheretherketone composites using drills with different geometries

[1]  F. Jiao,et al.  Modeling of cutting forces in helical milling of unidirectional CFRP considering carbon fiber fracture , 2021, Journal of Manufacturing Processes.

[2]  T. Ko,et al.  Influence of fiber direction and processing parameters on drilling temperature of CFRP , 2021, Journal of Mechanical Science and Technology.

[3]  R. Zitoune,et al.  In-situ cutting temperature and machining force measurements during conventional drilling of carbon fiber polymer composite laminates , 2021 .

[4]  Craig M. Hamel,et al.  Thermomechanical behaviors of polyether ether ketone (PEEK) with stretch-induced anisotropy , 2021 .

[5]  V. Knoblauch,et al.  Drilling induced defects on carbon fiber-reinforced thermoplastic polyamide and their effect on mechanical properties , 2021 .

[6]  Yuguo Sun,et al.  Mechanical behavior prediction of CF/PEEK-titanium hybrid laminates considering temperature effect by artificial neural network , 2020 .

[7]  T. Okabe,et al.  Experimental and numerical investigations on push-out delamination in drilling of composite laminates , 2020 .

[8]  J. Davim,et al.  On the machining behavior of carbon fiber reinforced polyimide and PEEK thermoplastic composites , 2020 .

[9]  K. Palanikumar,et al.  Measurement and analysis of thrust force and delamination in drilling glass fiber reinforced polypropylene composites using different drills , 2020 .

[10]  J. Paulo Davim,et al.  Advanced cutting tools and technologies for drilling carbon fibre reinforced polymer (CFRP) composites: A review , 2019, Composites Part A: Applied Science and Manufacturing.

[11]  Liangchi Zhang,et al.  Heat effect on the material removal in the machining of fibre-reinforced polymer composites , 2019, International Journal of Machine Tools and Manufacture.

[12]  Y. Du,et al.  Comprehensive investigation of cutting mechanisms and hole quality in dry drilling woven aramid fibre–reinforced plastic with typical tools , 2019, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture.

[13]  T. Ko,et al.  Study on chisel edge drilling behavior and step drill structure on delamination in drilling CFRP , 2018, Composite Structures.

[14]  Li Zhou,et al.  3D level comprehensive evaluation of hole quality in drilling carbon fiber-reinforced plastics , 2017 .

[15]  C. Bellini,et al.  In process monitoring of cutting temperature during the drilling of FRP laminate , 2017 .

[16]  K. Palanikumar,et al.  Optimization of delamination factor in drilling GFR–polypropylene composites , 2017 .

[17]  K. Palanikumar,et al.  Tool materials influence on surface roughness and oversize in machining glass fiber reinforced polypropylene (GFR-PP) composites , 2017 .

[18]  Gérard Poulachon,et al.  CFRP drilling: Fundamental study of local feed force and consequences on hole exit damage , 2015 .

[19]  K. Palanikumar,et al.  Thrust Force Analysis in Drilling Glass Fiber Reinforced/Polypropylene (GFR/PP) Composites , 2016 .

[20]  Hiroyuki Sasahara,et al.  Temperature measurement of cutting tool and machined surface layer in milling of CFRP , 2013 .

[21]  I. Amenabar,et al.  Experimental analysis of drilling damage in carbon-fiber reinforced thermoplastic laminates manufactured by resin transfer molding , 2012 .

[22]  João Manuel R. S. Tavares,et al.  Drilling tool geometry evaluation for reinforced composite laminates , 2010 .

[23]  Alexander Bismarck,et al.  Effect of hot water immersion on the performance of carbon reinforced unidirectional poly(ether ether ketone) (PEEK) composites: Stress rupture under end-loaded bending , 2007 .

[24]  Dave Kim,et al.  Influence of Consolidation Process on the Drilling Performance and Machinability of PIXA-M and PEEK Thermoplastic Composites , 2005 .

[25]  H. Hamada,et al.  Influence of processing conditions on bending property of continuous carbon fiber reinforced PEEK composites , 2004 .

[26]  H. Hocheng,et al.  MACHINABILITY OF SOME FIBER-REINFORCED THERMOSET AND THERMOPLASTICS IN DRILLING , 1993 .

[27]  H. Hocheng,et al.  On drilling characteristics of fiber-reinforced thermoset and thermoplastics , 1992 .