Cutting of Hardened Steel

[1]  R. Recht.  Catastrophic Thermoplastic Shear , 1964 .

[2]  M. C. Shaw,et al.  Mechanics of Saw-Tooth Chip Formation in Metal Cutting , 1999 .

[3]  S. L. Semiatin,et al.  Shear localization during metal cutting , 1983 .

[4]  Matthew A. Davies,et al.  On Chip Morphology, Tool Wear and Cutting Mechanics in Finish Hard Turning , 1996 .

[5]  Chun Liu,et al.  Single-step superfinish hard machining: Feasibility and feasible cutting conditions , 1996 .

[6]  H. Dubbel.  Taschenbuch für den maschinenbau , 1924 .

[7]  M. C. Shaw,et al.  Chip Formation in the Machining of Hardened Steel , 1993 .

[8]  M. C. Shaw,et al.  Tool Fracture at the End of a Cut—Part 1: Foot Formation , 1988 .

[9]  R. F. Recht,et al.  A Dynamic Analysis of High-Speed Machining , 1985 .

[10]  M. M. Barash,et al.  The Mechanical State of the Sublayer of a Surface Generated by Chip-Removal Process—Part 2: Cutting With a Tool With Flank Wear , 1976 .

[11]  W. Schatt.  Einführung in die werkstoffwissenschaft , 1982 .

[12]  Kazuo Nakayama,et al.  Machining Characteristics of Hard Materials , 1988 .

[13]  K. Malle.  Hartdrehen von Hinterachswellen , 1999 .

[14]  G. Sih.  Strain-energy-density factor applied to mixed mode crack problems , 1974 .

[15]  Edward M. Trent.  Cutting-tool materials , 1968 .

[16]  M. M. Barash,et al.  The Mechanical State of the Sublayer of a Surface Generated by Chip-Removal Process—Part 1: Cutting With a Sharp Tool , 1976 .

[17]  T. Matsuo,et al.  An Analysis of Saw-Toothed Chip Formation , 1982 .

[18]  Bo Lindström,et al.  Measurements of the Segmentation Frequency in the Chip Formation Process , 1983 .

[19]  Hossam A. Kishawy,et al.  Effects of process parameters on material side flow during hard turning , 1999 .

[20]  Günther Werner.  Kinematik und Mechanik des Schleifprozesses , 1971 .

[21]  M. M. Barash,et al.  Cutting mechanism during machining of hardened steel , 1987 .

[22]  M. Elbestawi,et al.  A Model for Chip Formation During Machining of Hardened Steel , 1996 .

[23]  R. Komanduri,et al.  Machining of Hard Materials , 1984 .

[24]  Takashi Ueda,et al.  Temperature Measurement of CBN Tool in Turning of High Hardness Steel , 1999 .

[25]  Y. Chou,et al.  Wear mechanisms of cubic boron nitride tools in precision turning of hardened steels , 1994 .

[26]  S. A. Klimenko,et al.  On the wear mechanism of cubic boron nitride base cutting tools , 1992 .

[27]  R. Komanduri,et al.  On a Thermomechanical Model of Shear Instability in Machining , 1995 .

[28]  Γεωργιοσ Χρυσολουρησ.  EINSATZ HOCHHARTER POLYKRISTALLINER SCHNEIDSTOFFE ZUM DREHEN UND FRASEN , 1979 .

[29]  H. Laub,et al.  HARTDREHEN ERSETZT SCHLEIFEN , 1999 .