IMPACTS OF SUPERALLOYS ON THE SURFACE QUALITY OF ADDITIVELY MANUFACTURED CHANNELS

Solar

[1]  Tianyu Zhang,et al.  Understanding surface roughness on vertical surfaces of 316 L stainless steel in laser powder bed fusion additive manufacturing , 2022, Powder Technology.

[2]  K. Thole,et al.  IMPACTS OF THE ADDITIVE MANUFACTURING PROCESS ON THE ROUGHNESS OF ENGINE SCALE VANES AND COOLING CHANNELS , 2022, Journal of Turbomachinery.

[3]  K. Thole,et al.  AMPLITUDE AND WAVELENGTH EFFECTS FOR WAVY CHANNELS , 2022, Journal of Turbomachinery.

[4]  K. Thole,et al.  Impacts of Pin Fin Shape and Spacing on Heat Transfer and Pressure Losses , 2022, Journal of Turbomachinery.

[5]  T. Pollock,et al.  Microstructure Evolution and Tensile Properties of a Selectively Laser Melted CoNi-Base Superalloy , 2022, Metallurgical and Materials Transactions A.

[6]  G. Nicoletto,et al.  A comparison of Inconel 718 obtained with three L-PBF production systems in terms of process parameters, as-built surface quality, and fatigue performance , 2022, International Journal of Fatigue.

[7]  V. Hagenmeyer,et al.  Down-facing surfaces in laser powder bed fusion of Ti6Al4V: Effect of dross formation on dimensional accuracy and surface texture , 2021 .

[8]  A. Clare,et al.  Powder Bed Fusion of nickel-based superalloys: A review , 2021 .

[9]  Xinhua Wu,et al.  Process variation in Laser Powder Bed Fusion of Ti-6Al-4V , 2021, Additive Manufacturing.

[10]  R. Dehoff,et al.  A defect-resistant Co–Ni superalloy for 3D printing , 2020, Nature Communications.

[11]  B. Weigand,et al.  Experimental and Numerical Investigation on an Additively Manufactured Gas Turbine Ring Segment With an In-Wall Cooling Scheme , 2019, Heat Transfer.

[12]  Annamaria Gisario,et al.  Metal additive manufacturing in the commercial aviation industry: A review , 2019, Journal of Manufacturing Systems.

[13]  Jacob C. Snyder,et al.  Effect of Additive Manufacturing Process Parameters on Turbine Cooling , 2019, Journal of Turbomachinery.

[14]  Veit Hagenmeyer,et al.  Effect of Process Parameters on the Generated Surface Roughness of Down-Facing Surfaces in Selective Laser Melting , 2019, Applied Sciences.

[15]  Ming Yan,et al.  Selective laser melting of typical metallic materials: An effective process prediction model developed by energy absorption and consumption analysis , 2019, Additive Manufacturing.

[16]  Carlo Cavallini,et al.  Development of Laser-Based Powder Bed Fusion Process Parameters and Scanning Strategy for New Metal Alloy Grades: A Holistic Method Formulation , 2018, Materials.

[17]  Ehsan Malekipour,et al.  Common defects and contributing parameters in powder bed fusion AM process and their classification for online monitoring and control: a review , 2018 .

[18]  Patrick F. Dunn,et al.  Measurement and Data Analysis for Engineering and Science , 2017 .

[19]  Curtis K. Stimpson,et al.  Repeatability in Performance of Micro Cooling Geometries Manufactured with Laser Powder Bed Fusion , 2017 .

[20]  Yang Liu,et al.  Theoretical and experimental study on surface roughness of 316L stainless steel metal parts obtained through selective laser melting , 2016 .

[21]  Francesco Trevisan,et al.  Study of Internal Channel Surface Roughnesses Manufactured by Selective Laser Melting in Aluminum and Titanium Alloys , 2016, Metallurgical and Materials Transactions A.

[22]  Jay Patel,et al.  Additive manufacturing , 2016, XRDS.

[23]  Karen A. Thole,et al.  Build Direction Effects on Microchannel Tolerance and Surface Roughness , 2015 .

[24]  Karen A. Thole,et al.  Roughness Effects on Flow and Heat Transfer for Additively Manufactured Channels , 2015 .

[25]  F. Calignano,et al.  Influence of process parameters on surface roughness of aluminum parts produced by DMLS , 2012, The International Journal of Advanced Manufacturing Technology.

[26]  Carlo Nonino,et al.  EFFECT OF ASPECT RATIO ON CONVECTION ENHANCEMENT IN WAVY CHANNELS , 2003 .

[27]  M. Konter,et al.  Materials and manufacturing of advanced industrial gas turbine components , 2001 .

[28]  R. Webb,et al.  Forced convection heat transfer in helically rib-roughened tubes , 1980 .

[29]  C F Colebrook,et al.  TURBULENT FLOW IN PIPES, WITH PARTICULAR REFERENCE TO THE TRANSITION REGION BETWEEN THE SMOOTH AND ROUGH PIPE LAWS. , 1939 .

[30]  S. Forsik,et al.  Development of a New Alumina-Forming Crack-Resistant High-γ′ Fraction Ni-Base Superalloy for Additive Manufacturing , 2020 .

[31]  Xinhua Wu,et al.  Influences of processing parameters on surface roughness of Hastelloy X produced by selective laser melting , 2017 .

[32]  V. Gnielinski.  New equations for heat and mass transfer in the turbulent flow in pipes and channels , 1975 .

[33]  Henry Cohen,et al.  Gas turbine theory , 1973 .