Machinability study of tungsten carbide using PCD tools under ultrasonic elliptical vibration cutting

Abstract Sintered tungsten carbide (WC) is an extremely hard and brittle material extensively used in tool manufacturing industries. However, the current cutting technologies for shaping this typical hard-to-machine material are still cost ineffective. In this study, polycrystalline diamond (PCD) tools are used to study the machinability of sintered WC (~15% Co) by applying the ultrasonic elliptical vibration cutting (UEVC) technique. Firstly, it presents the UEVC principle and the effects of speed ratio (i.e. the ratio of the nominal cutting speed to the maximum tool vibration speed in the cutting direction) on the tool–workpiece relative motion as the cutting speed greatly influences the UEVC performance. Then UEVC experiments are carried out to analyze the cutting force, tool-wear progression, chip formation and surface quality against the cutting time at different speed ratios. The results show that when the speed ratio decreases, the resultant cutting force and the tool flank wear decrease while the surface finish improves. Average surface roughness, Ra, in a range between 0.030 and 0.050 μm is achieved at speed ratios less than 0.107. The experimental findings suggest that the commercial PCD tools can be used to machine sintered WC to achieve ultraprecision surface by applying the UEVC technique, which will be cost effective for miniature cutting technologies in future.

[1]  E. Shamoto,et al.  Elliptical Vibration Cutting of Tungsten Alloy Molds for Optical Glass Parts , 2007 .

[2]  Mahmudur Rahman,et al.  Effect of machining parameters in ultrasonic vibration cutting , 2008 .

[3]  Bin Zhao,et al.  Research on the vibration cutting performance of particle reinforced metallic matrix composites SiCp/Al , 2002 .

[4]  Toshimichi Moriwaki,et al.  Development of Ultrasonic Elliptical Vibration Controller for Elliptical Vibration Cutting , 2002 .

[5]  Kui Liu,et al.  CBN tool wear in ductile cutting of tungsten carbide , 2003 .

[6]  Eiji Shamoto,et al.  Study on Elliptical Vibration Cutting , 1994 .

[7]  A V Mitrofanov,et al.  Ultrasonically assisted turning of aviation materials: simulations and experimental study. , 2004, Ultrasonics.

[8]  E. Shamoto,et al.  Ultraprecision micromachining of brittle materials by applying ultrasonic elliptical vibration cutting , 2004, Micro-Nanomechatronics and Human Science, 2004 and The Fourth Symposium Micro-Nanomechatronics for Information-Based Society, 2004..

[9]  Junichiro Kumabe,et al.  Ultrasonic superposition vibration cutting of ceramics , 1989 .

[10]  Eiji Shamoto,et al.  Elliptical Vibration Cutting. (2nd Report). Study on Effects of Vibration Conditions. , 1999 .

[11]  Eiji Shamoto,et al.  Ultraprecision micromachining of hardened steel by applying ultrasonic elliptical vibration cutting , 2003, MHS2003. Proceedings of 2003 International Symposium on Micromechatronics and Human Science (IEEE Cat. No.03TH8717).

[12]  L. Balamuth.  Ultrasonic assistance to conventional metal removal , 1966 .

[13]  M. Xiao,et al.  The effect of tool geometry on regenerative instability in ultrasonic vibration cutting , 2006 .

[14]  J. M. Casstevens,et al.  Diamond Turning Optical Surfaces On Electroless Nickel , 1978, Optics & Photonics.

[15]  Deyuan Zhang,et al.  Ultrasonic elliptical vibration transducer driven by single actuator and its application in precision cutting , 2006 .

[16]  M. Rahman,et al.  A study on ultrasonic elliptical vibration cutting of tungsten carbide , 2009 .

[17]  J. Kumabe,et al.  Super-precision cylindrical machining , 1984 .