Process mechanisms based on powder flow spatial distribution in direct metal deposition

Abstract Direct Metal Deposition (DMD) is becoming increasingly attention-attracting technology for new component manufacture and repair. However, fundamental process understanding is not yet comprehensive. Without considering the realistic spatial distribution of powder flow, some important process conditions have been neglected in layered deposition, such as the initial stand-off distance of nozzle, scanning direction (orientation of nozzle), change in stand-off distance through process and stability of multi-layer deposition. This then limits the efficacy of deposition strategies which serves to limit the industrial uses of DMD. In this paper, a realistic model was built for the simulation of multi-layer deposition, using real spatial powder flow concentration. Then, the influences of the orientation of nozzle, the stand-off distance of nozzle and single-step rise on geometric characteristics are investigated. It is showed that the stand-off distance of nozzle significantly affects the geometric characteristics of the deposited layer thickness, while the influence of the orientation of four-tip nozzle on deposition can largely be neglected. Furthermore, the stability of multi-layer deposition was discussed, and the steady condition was obtained by analyzing relation among single-step rise, maximum deposited layer thickness and stand-off distance of nozzle. This also allows a deposition strategy to be optimized for the purpose of manufacturing given procedure. The approach taken here is also verified by experiments with the strategies proposed by simulation.

[1]  Andrew J. Pinkerton,et al.  The significance of deposition point standoff variations in multiple-layer coaxial laser cladding (coaxial cladding standoff effects) , 2004 .

[2]  Aitzol Lamikiz,et al.  Modeling of the geometry built-up by coaxial laser material deposition process , 2014 .

[3]  Shaukat Ali Shah,et al.  Parametric study of development of Inconel-steel functionally graded materials by laser direct metal deposition , 2014 .

[4]  R. Poprawe,et al.  A comparative study of Inconel 718 formed by High Deposition Rate Laser Metal Deposition with GA powder and PREP powder , 2016 .

[5]  Weidong Huang,et al.  Development of powder flow model of laser solid forming by analysis method , 2016 .

[6]  Changmeng Liu,et al.  Microstructural characterization of laser melting deposited Ti–5Al-5Mo–5V–1Cr–1Fe near β titanium alloy , 2013 .

[7]  Weidong Huang,et al.  The influences of processing parameters on forming characterizations during laser rapid forming , 2003 .

[8]  Andrew J. Pinkerton,et al.  An analytical model of energy distribution in laser direct metal deposition , 2004 .

[9]  Lijun Li,et al.  Effects of process variables on laser direct formation of thin wall , 2007 .

[10]  Karen M. Taminger,et al.  Ti-Fe Intermetallics Analysis and Control in Joining Titanium Alloy and Stainless Steel by Laser Metal Deposition , 2017 .

[11]  Remy Fabbro,et al.  Influence of various process conditions on surface finishes induced by the direct metal deposition laser technique on a Ti-6Al-4V alloy , 2013 .

[12]  Weidong Huang,et al.  Experiment study of powder flow feed behavior of laser solid forming , 2012 .

[13]  Kai Zhang,et al.  Research on the processing experiments of laser metal deposition shaping , 2007 .

[14]  E. Toyserkani,et al.  3-D finite element modeling of laser cladding by powder injection: effects of laser pulse shaping on the process , 2004 .

[15]  D. Rosenthal.  Mathematical Theory of Heat Distribution during Welding and Cutting , 1941 .

[16]  P. Michaleris.  Modeling metal deposition in heat transfer analyses of additive manufacturing processes , 2014 .

[17]  E. Toyserkani,et al.  A 3D dynamic numerical approach for temperature and thermal stress distributions in multilayer laser solid freeform fabrication process , 2007 .