Crash behavior of thin-Walled box beams with complex sinusoidal relief patterns

Abstract This paper proposes a new automotive box-beam crash absorber design with sinusoidal patterns embedded on the beam surfaces. Six different types of surface patterns were initially proposed and a total of 43 samples were simulated using the commercial pre-processor HyperCrash™ and the commercial explicit FEM solver RADIOSS™. The aim of the study is to improve energy absorption properties of the beams by controlling the wavelength of progressive buckle formations and obtaining denser collapse formations. It was found that the relief patterns could be used effectively to change the buckling modes and reduce the buckle wavelength. A maximum of 42 percent increase in the amount of total energy absorbed and an increase in the energy efficiency factor from 1.08 to 1.54 was observed moving from the reference model to the best design so far. This research may possibly pave new avenues in crash absorber design.

[1]  Seyed Jamal Hosseinipour,et al.  Energy absorbtion and mean crushing load of thin-walled grooved tubes under axial compression , 2003 .

[2]  Tomasz Wierzbicki,et al.  Weight and crash optimization of foam-filled three-dimensional “S” frame , 2002 .

[3]  D. Kecman.  An engineering approach to crashworthiness of thin-walled beams and joints in vehicle structures , 1997 .

[4]  Norman Jones,et al.  Energy-absorbing effectiveness factor , 2010 .

[5]  Tomasz Wierzbicki,et al.  Crash behavior of box columns filled with aluminum honeycomb or foam , 1998 .

[6]  O. Hopperstad,et al.  Optimum design for energy absorption of square aluminium columns with aluminium foam filler , 2001 .

[7]  F. Rammerstorfer,et al.  Experimental studies on the quasi-static axial crushing of steel columns filled with aluminium foam , 2000 .

[8]  Norman Jones,et al.  Dynamic progressive buckling of circular and square tubes , 1986 .

[9]  Yucheng Liu.  Improved concept models for straight thin-walled columns with box cross section , 2008 .

[10]  W. Abramowicz,et al.  Thin-walled structures as impact energy absorbers , 2003 .

[11]  J. M. Alexander.  AN APPROXIMATE ANALYSIS OF THE COLLAPSE OF THIN CYLINDRICAL SHELLS UNDER AXIAL LOADING , 1960 .

[12]  S. Reid,et al.  Static and dynamic axial crushing of foam-filled sheet metal tubes , 1986 .

[13]  W. Abramowicz,et al.  Dynamic axial crushing of square tubes , 1984 .

[14]  Jae-Eung Oh,et al.  EFFECT OF TRIGGERING ON THE ENERGY ABSORPTION CAPACITY OF AXIALLY COMPRESSED ALUMINUM TUBES , 1999 .

[15]  T. Wierzbicki,et al.  On the Crushing Mechanics of Thin-Walled Structures , 1983 .

[16]  T. Wierzbicki,et al.  Axial Crushing of Multicorner Sheet Metal Columns , 1989 .

[17]  Tongxi Yu,et al.  Axial crushing of circular tubes with buckling initiators , 2009 .

[18]  O. Hopperstad,et al.  Static and dynamic crushing of square aluminium extrusions with aluminium foam filler , 2000 .

[19]  Zhong You,et al.  Energy absorption of axially compressed thin-walled square tubes with patterns , 2007 .

[20]  G. Cheng,et al.  Theoretical prediction and numerical simulation of multi-cell square thin-walled structures , 2006 .

[21]  Yucheng Liu,et al.  Optimum design of straight thin-walled box section beams for crashworthiness analysis , 2008 .

[22]  Heung-Soo Kim,et al.  New extruded multi-cell aluminum profile for maximum crash energy absorption and weight efficiency , 2002 .

[23]  Jialing Yang,et al.  Energy-absorption behavior of a metallic double-sine-wave beam under axial crushing , 2009 .