Evaluation of metal matrix composite to replace spheroidal graphite iron for a critical component, steering knuckle

Abstract Steering knuckle is considered as one of the critical component in automotive suspension system. It is subjected to time varying loads during its service life, leading to fatigue failure. Therefore, its design is an important aspect in the product development cycle. Currently, spheroidal graphite (SG) iron is widely used to manufacture steering knuckle in the commercial automobile sector. It has been observed from the knuckle manufacturers that advanced materials and weight reduction are the real need for the current automobile industry. Due to their high strength to weight ratio, Metal Matrix Composites (MMCs) have the potential to meet the demanded design requirements of the automotive industry, compared to conventional materials. In this work, an aluminum alloy reinforced with titanium carbide particulate is suggested as an alternate material in place of existing SG iron. Structural analysis of steering knuckle made of alternate material Al-10 wt.% TiC was performed using commercial code ANSYS. The results of steering knuckle made of MMC (Al-10 wt.% TiC) were compared with that of aluminum alloy and SG iron steering knuckles for its performance based on real time load cases. It is found from this analysis, the knuckle strut region has maximum stress and deflection during its life time. The critical strut region cross section area of knuckle was analyzed and geometrically optimized for minimum bending stress and deflection using genetic algorithm available in MatLab. Since, the knuckle experiences time varying loads, fatigue analysis also performed on MMC model before and after optimization. The life of the MMC knuckle is evaluated for maximum load case. The results obtained from numerical analysis and experimental testing encouraged using particulate reinforced metal matrix composites for critical component steering knuckle with a weight saving about 55% when compared with currently used SG iron.

[1]  Stephen Wolfram,et al.  The Mathematica Book , 1996 .

[2]  R. Gadelrab,et al.  The effects of aging on the hardness and fatigue behavior of 2024 Al alloy/SiC composites , 2002 .

[3]  Cevdet Kaynak,et al.  Effects of SiC particulates on the fatigue behaviour of an Al-alloy matrix composite , 2006 .

[4]  R. L. Jhala,et al.  Component Fatigue Behaviors And Life Predictions Of A Steering Knuckle Using Finite Element Analysis , 2009 .

[5]  Wilfried Eichlseder,et al.  Fatigue analysis by local stress concept based on finite element results , 2002 .

[6]  G. K. Triantafyllidis,et al.  Fracture Characteristics of Fatigue Failure of a Vehicle’s Ductile Iron Steering Knuckle , 2009 .

[7]  N. Chawla,et al.  Metal Matrix Composites: Automotive Applications , 2006 .

[8]  C. Selcuk,et al.  Al–TiC composite made by the addition of master alloys pellets synthesised from reacted elemental powders , 2006 .

[9]  Michael Hack,et al.  Improving the fatigue life of a vehicle knuckle with a reliability-based design optimization approach , 2009 .

[10]  Development of low cost metal matrix composites for commercial applications , 2000 .

[11]  T. Eden,et al.  Fatigue behavior of SiC particulate reinforced spray-formed 7XXX series Al-alloys , 2011 .

[12]  I. Rajendran,et al.  Wear behaviour of A356/25SiCp aluminium matrix composites sliding against automobile friction material , 2006 .

[13]  S. Vijayarangan,et al.  Optimal design of a composite leaf spring using genetic algorithms , 2001 .

[14]  R. Hibbeler.  Statics and Mechanics of Materials , 1995 .

[15]  A. Sili,et al.  Improvement of the fatigue behaviour of Al 6061/20% SiCp composites by means of titanium coatings , 2001 .

[16]  Yuji Nakasone,et al.  Engineering Analysis with ANSYS Software , 2007 .