The effect of surface grinding and sandblasting on flexural strength and reliability of Y-TZP zirconia ceramic.

OBJECTIVES This study was conducted to evaluate the effect of grinding and sandblasting on the microstructure, biaxial flexural strength and reliability of two yttria stabilized tetragonal zirconia (Y-TZP) ceramics. METHODS Two Y-TZP powders were used to produce fine grained and coarse grained microstructures. Sixty discs from each material were randomly divided into six groups of ten. For each group, a different surface treatment was applied: dry grinding, wet grinding, sandblasting, dry grinding + sandblasting, sandblasting + dry grinding and a control group. Biaxial flexural strength was determined and data were analyzed using one-way ANOVA, followed by Tukey's HSD test (p < 0.05). In addition, Weibull statistics was used to analyze the variability of flexural strength. The relative amount of transformed monoclinic zirconia, corresponding transformed zone depth (TZD) and the mean critical defect size Ccr were calculated. RESULTS There was no difference in mean strength between the as sintered fine and coarse grained Y-TZP. Significant differences (p < 0.05) were found between the control group and ground fine grained material for both wet and dry grinding. Sandblasting significantly increased the strength in fine and coarse grained materials. All surface treatment procedures reduced the Weibull modulus of Y-TZP. For both materials, the highest amount of the monoclinic phase and the largest TZD was found after sandblasting. Lower amounts of the monoclinic phase were obtained after both grinding procedures, where the highest mean critical defect size Ccr was also calculated. SIGNIFICANCE Our results indicate that sandblasting may provide a powerful technique for strengthening Y-TZP in clinical practice. In contrast, grinding may lead to substantial strength degradation and reduced reliability of prefabricated zirconia elements, therefore, sandblasting of ground surfaces is suggested.

[1]  B. Lawn Fracture of Brittle Solids by Brian Lawn , 1993 .

[2]  M. Persson,et al.  Organic Silanes and Titanates as Processing Additives for Injection Molding of Ceramics , 1989 .

[3]  R P Kusy,et al.  Zirconia brackets: an evaluation of morphology and coefficients of friction. , 1994, American journal of orthodontics and dentofacial orthopedics : official publication of the American Association of Orthodontists, its constituent societies, and the American Board of Orthodontics.

[4]  Michael V. Swain,et al.  Metastability of the Martensitic Transformation in a 12 mol% Ceria‐Zirconia Alloy: II, Grinding Studies , 1989 .

[5]  J. E. Ritter Particle Impact Damage of Engineering Ceramics , 1992 .

[6]  E. C. Subbarao,et al.  Zirconia - an overview , 1981 .

[7]  Anil V. Virkar,et al.  Ferroelastic Domain Switching as a Toughening Mechanism in Tetragonal Zirconia , 1986 .

[8]  P. Nicholson,et al.  Phase Analysis in Zirconia Systems , 1972 .

[9]  B. Lawn,et al.  A Critical Evaluation of Indentation Techniques for Measuring Fracture Toughness: II, Strength Method , 1981 .

[10]  R. Rice STRENGTH/GRAIN-SIZE EFFECTS IN CERAMICS. , 1972 .

[11]  N. Claussen,et al.  X‐Ray Determination of Transformation Depths in Ceramics Containing Tetragonal ZrO2 , 1981 .

[12]  P Schärer,et al.  Zirconia posts: a new all-ceramic concept for nonvital abutment teeth. , 1995, Journal of esthetic dentistry.

[13]  D. J. Green A Technique for Introducing Surface Compression into Zirconia Ceramics , 1983 .

[14]  S. Hondrum A review of the strength properties of dental ceramics. , 1992, The Journal of prosthetic dentistry.

[15]  G. M. Wolten Diffusionless Phase Transformations in Zirconia and Hafnia , 1963 .

[16]  E. D. Rekow,et al.  Mechanical Characterization of Dental Ceramics by Hertzian Contacts , 1998, Journal of dental research.

[17]  J. Rödel,et al.  Reliability of alumina ceramics: Effect of grain size , 1995 .

[18]  J. E. Ritter Erosion of Ceramic Materials , 1992 .

[19]  T. Gupta Strengthening by Surface Damage in Metastable Tetragonal Zirconia , 1980 .

[20]  M. Kern,et al.  Bonding to zirconia ceramic: adhesion methods and their durability. , 1998, Dental materials : official publication of the Academy of Dental Materials.

[21]  M. Swain Grain-size dependence of toughness and transformability of 2mol% Y-TZP ceramics , 1986 .

[22]  R. Luthardt,et al.  KRONEN AUS HOCHLEISTUNGSKERAMIK : ZIRKONDIOXID-KERAMIK, EIN NEUER WERKSTOFF IN DER KRONENPROTHETIK , 1998 .