High-Order Bending Analysis of Unidirectional Curved ‘‘Soft’’ Sandwich Panels with Disbonds and Slipping Layers

The bending behavior of unidirectional singly curved sandwich panels with a ‘‘soft’’ core and delaminated (debonded) zones or slipping layers is described herein. The delaminated zone is assumed to exist through the width of the panels, and is in the form of an interfacial debonded zone at one of the face–core interfaces, thus subdividing the length of the panel into three zones, i.e. two fully bonded zones and one that is debonded (delaminated). The formulation uses an interfacial spring description, i.e. distributed shear and radial normal springs at the face–core interfaces, to model the effects of the slipping layers and the various delaminated (debonded) zones. The formulation is based on a closed-form high-order approach (HSAPT) that incorporates the high-order effects of the ‘‘soft’’ core. The variational approach is used to derive the governing equations along with the general explicit boundary and continuity conditions. A typical curved sandwich panel with an inner or an edge delamination, with or without contact, subjected to a distributed load and pinned supports is discussed. A comparison between the various delamination types and the fully bonded case is presented in terms of the displacements, stresses and internal stress resultants of the faces and in the vicinity of the edges of the delaminated zones. Finally, the effect of slipping interfacial layers, with or without contact when subjected to a distributed load, is considered and compared with the behavior of a fully bonded sandwich panel. From the numerical studies it is found that the membrane action of the face sheets plays a major role in the overall structural resistance of the sandwich panel compared to that of flat panels. However, in the near vicinity of the edges of the debonded zone, the membrane action does not prevent the interfacial stresses to reach very large values in the case of delamination without contact. For all of the delamination types, contact exerts a favorable effect, in the sense that the induced interfacial stresses are much smaller when compared to cases of delamination without contact.

[1]  J. Vinson.  The Behavior of Sandwich Structures of Isotropic and Composite Materials , 1999 .

[2]  Chien-Chang Lin,et al.  Local buckling of delaminated composite sandwich plates , 1996 .

[3]  Y. Frostig,et al.  Nonlinear High-Order Analysis of Cracked RC Beams Strengthened with FRP Strips , 2001 .

[4]  Y. Frostig,et al.  Higher-Order Buckling of Debonded (Delaminated ) Sandwich Panels with Soft Core , 2000 .

[5]  Yeoshua Frostig,et al.  High‐Order Theory for Sandwich‐Beam Behavior with Transversely Flexible Core , 1992 .

[6]  Yeoshua Frostig,et al.  Free Vibrations of Curved Sandwich Beams with a Transversely Flexible Core , 2001 .

[7]  Liviu Librescu,et al.  Effects of Tangential Edge Constraints on the Postbuckling Behavior of Flat and Curved Panels Subjected to Thermal and Mechanical Loads , 1994 .

[8]  H.-R. Meyer-Piening,et al.  Buckling analysis of FRP faced cylindrical sandwich panel under combined loading , 1990 .

[9]  B. C. Nakra,et al.  Vibration and damping analysis of curved sandwich beams with a visoelastic core , 1988 .

[10]  A. Kühhorn,et al.  A nonlinear theory for sandwich shells including the wrinkling phenomenon , 1992 .

[11]  Tarun Kant,et al.  C0 Finite element geometrically non-linear analysis of fibre reinforced composite and sandwich laminates based on a higher-order theory , 1992 .

[12]  Yeoshua Frostig,et al.  Behavior of delaminated sandwich beam with transversely flexible core — high order theory , 1992 .

[13]  F. J. Plantema,et al.  Sandwich Construction: The Bending and Buckling of Sandwich Beams, Plates and Shells , 1966 .

[14]  H. G. Allen.  Analysis and design of structural sandwich panels , 1969 .

[15]  Yeoshua Frostig,et al.  High-order behavior of fully bonded and delaminated circular sandwich plates with laminated face sheets and a “soft” core , 2002 .

[16]  Elena Bozhevolnaya,et al.  Nonlinear closed-form high-order analysis of curved sandwich panels , 1997 .

[17]  Ole Thybo Thomsen,et al.  Analysis and Parametric Study of Non-Circular Pressurized Sandwich Fuselage Cross Section Using a High-Order Sandwich Theory Formulation , 2001 .

[18]  C. Hwu,et al.  Buckling and postbuckling of delaminated composite sandwich beams , 1992 .

[19]  Bhavani V. Sankar,et al.  Compressive Failure of Sandwich Beams with Debonded Face-Sheets , 2000 .

[20]  Yeoshua Frostig,et al.  Bending of Curved Sandwich Panels with a Transversely Flexible Core-Closed-Form High-Order Theory , 1999 .

[21]  Sture Smidt,et al.  Bending of curved sandwich beams , 1995 .

[22]  Dan Zenkert,et al.  Strength of sandwich beams with interface debondings , 1991 .

[23]  G. J. Simitses,et al.  Effect of delamination of axially loaded homogeneous laminated plates , 1985 .

[24]  Ahmed K. Noor,et al.  Computational Models for Sandwich Panels and Shells , 1996 .

[25]  E. Carrera,et al.  STATIC BUCKLING OF MODERATELY THICK, ANISOTROPIC, LAMINATED AND SANDWICH CYLINDRICAL SHELL PANELS , 1990 .

[26]  Haim Abramovich,et al.  Influence of predetermined delaminations on buckling and postbuckling behavior of composite sandwich beams , 1991 .

[27]  Göran Tolf.  Stresses in a curved laminated beam , 1983 .

[28]  Liviu Librescu,et al.  Recent developments in the modeling and behavior of advanced sandwich constructions: a survey , 2000 .