Abrasive wear behavior of monolithic alloy, homogeneous and functionally graded aluminum (LM25/AlN and LM25/SiO2) composites

ABSTRACT Functionally graded metal matrix composites (MMCs) and homogenous composites (Al/AlN and Al/SiO2-10 wt%) have been fabricated through centrifugal casting and liquid metallurgy route, respectively. The properties of these composites were compared with aluminum alloy. Microstructural characteristics and hardness were studied on the surfaces of functionally graded materials (FGMs), homogenous composites, and unreinforced aluminum alloy using an optical microscope and a Vickers micro hardness tester, respectively. Tensile test was carried out on the outer and inner sections of FGMs and specimens from homogenous composites and alloy utilizing universal testing machines (UTMs). Three-body abrasive wear test was conducted for different loads and speeds to study their effect on the surfaces of composites and alloy using dry abrasion tester. Microstructural and hardness results reveal that the outer surface of aluminum nitride (AlN)-reinforced FGM has a particle-enriched region with the highest hardness. Tensile strength was found higher in both homogenous composites compared to zones of their FGMs. Abrasion wear rate was found increased with increase in load and decreased with increase in speed. The outer surface of AlN-reinforced FGM has higher wear resistance followed by the outer surface of SiO2-reinforced FGM. Scanning Electron Microscopy (SEM) analysis was performed on worn-out surfaces and observed particle-enriched outer surface of Al/AlN FGM with less abrasion.

[1]  N. Radhika,et al.  Experimental Investigation on Abrasive Wear Behavior of Functionally Graded Aluminum Composite , 2015 .

[2]  O. Pandey,et al.  Effect of Particle Size on Wear Behavior of Al–Garnet Composites , 2015 .

[3]  T. Rajmohan,et al.  The influence of alumina on mechanical and tribological characteristics of graphite particle reinforced hybrid Al-MMC , 2014 .

[4]  A. Patnaik,et al.  Comparative investigations on three-body abrasive wear behavior of long and short glass fiber-reinforced epoxy composites , 2014 .

[5]  R. Kayikci,et al.  Production of Functionally Graded AlB2/Al-4%Mg Composite by Centrifugal Casting , 2013 .

[6]  Belete Sirahbizu Yigezu,et al.  Influence of Reinforcement Type on Microstructure, Hardness, and Tensile Properties of an Aluminum Alloy Metal Matrix Composite , 2013 .

[7]  N. Radhika,et al.  Effect of reinforcement on wear behaviour of aluminium hybrid composites , 2013 .

[8]  Raṅganātha,et al.  INVESTIGATION ON THREE BODY ABRASIVE WEAR OF Al 2 O 3 FILLER ON CFRP COMPOSITES , 2013 .

[9]  Esther T. Akinlabi,et al.  Functionally graded material: an overview , 2012, WCE 2012.

[10]  Maksim Antonov,et al.  Effect of temperature and load on three-body abrasion of cermets and steel , 2012 .

[11]  A. Çanakçı.  Microstructure and abrasive wear behaviour of B4C particle reinforced 2014 Al matrix composites , 2011 .

[12]  Jincheng Wang,et al.  Mechanical properties and fracture mechanisms of aluminum matrix composites reinforced by Al9(Co, Ni)2 intermetallics , 2010 .

[13]  王锦程,et al.  Mechanical properties and fracture mechanisms of aluminum matrix composites reinforced by Al_9（Co,Ni）_2 intermetallics , 2010 .

[14]  B. C. Pai,et al.  Formation of solidification microstructures in centrifugal cast functionally graded aluminium composites , 2009 .

[15]  V. Chawla,et al.  Development of Aluminium Based Silicon Carbide Particulate Metal Matrix Composite , 2009 .

[16]  A. C. Vieira,et al.  Dry sliding wear of Al alloy/SiCp functionally graded composites: Influence of processing conditions , 2009 .

[17]  K. Sridharan,et al.  Microstructure and properties of functionally graded Al–Mg–B composites fabricated by centrifugal casting , 2008 .

[18]  T. Matikas,et al.  Microdeformation behaviour of Al–SiC metal matrix composites , 2008 .

[19]  D. Mondal,et al.  High stress abrasive wear behaviour of aluminium hard particle composites: Effect of experimental parameters, particle size and volume fraction , 2006 .

[20]  N. B. Duque,et al.  Functionally graded aluminum matrix composites produced by centrifugal casting , 2005 .

[21]  E. Candan,et al.  Abrasive wear behavior and mechanical properties of Al-Si/SiC composites , 2004 .

[22]  Y. Şahin.  Wear behaviour of aluminium alloy and its composites reinforced by SiC particles using statistical analysis , 2003 .

[23]  B. Kiebacka,et al.  Processing techniques for functionally graded materials , 2003 .

[24]  Ramón Rodríguez-Castro,et al.  Microstructure and mechanical behavior of functionally graded Al A359/SiCp composite , 2002 .

[25]  A. H. Yegneswaran,et al.  Three-body abrasion of a cast zinc–aluminium alloy: influence of Al2O3 dispersoid and abrasive medium , 2001 .

[26]  Chao-Yang Wang,et al.  Modeling the solidification of functionally graded materials by centrifugal casting , 2000 .