Characteristics of turbulent flow distribution in branch piping system

Flow distribution in branch piping system is affected by flow characteristics and different geometric variations. Most of the flow distribution studies are performed with one-dimensional analysis to yield overall information only. However, detailed analysis is required to find effects of design parameters on the flow distribution. For this aspect, three-dimensional turbulent flow analysis was performed to assess turbulence model performance and effects of upstream pressure and branch pipe geometry. Three different turbulence models of standard k-ɛ model, realizable k-ɛ model and standard k-ω yield similar results, indicating small effects of turbulence models on flow characteristics analysis. Geometric variations include area ratio of main and branch pipes, branch pipe diameter, and connection shape of main and branch pipes. Among these parameters, area ratio and branch diameter and shape show strong effect on flow distribution due to high friction and minor loss. Uniform flow distribution is one of common requirements in the branch piping system and this can be achieved with rather high total loss design.

[1]  D. K. Chandraker,et al.  Experimental and analytical investigations on core flow distribution and pressure distribution in the outlet header of a PHWR , 2002 .

[2]  T. Brunschwiler,et al.  3D Integrated Water Cooling of a Composite Multilayer Stack of Chips , 2010 .

[3]  Sreenivas Jayanti,et al.  Flow distribution and pressure drop in parallel-channel configurations of planar fuel cells , 2005 .

[4]  W. M. Taama,et al.  Modeling Flow Distribution for Internally Manifolded Direct Methanol Fuel Cell Stacks , 2000 .

[5]  R. Bajura,et al.  Flow Distribution Manifolds , 1976 .

[6]  K. Min,et al.  Numerical Analysis of the Gas Flow Distribution Characteristics in the Anode Flow Channel of Molten Carbonate Fuel Cell (MCFC) , 2009 .

[7]  Søren Knudsen Kær,et al.  Flow and Pressure Distribution in Fuel Cell Manifolds , 2010 .

[8]  Ephraim M Sparrow,et al.  Turbulence modeling for flow in a distribution manifold , 2009 .

[9]  Shiauh-Ping Jung,et al.  Flow distribution in the manifold of PEM fuel cell stack , 2007 .

[10]  Yong-hao Luo,et al.  Analytical and Experimental Investigation of Flow Distribution in Manifolds for heat Exchangers , 1998 .

[11]  R. A. Bajura,et al.  A Model for Flow Distribution in Manifolds , 1971 .

[12]  W. M. Taama,et al.  Pressure drop modelling for liquid feed direct methanol fuel cells Part II. Model based parametric analysis , 1999 .

[13]  S. Patankar.  Numerical Heat Transfer and Fluid Flow , 2018, Lecture Notes in Mechanical Engineering.

[14]  Ephraim M Sparrow,et al.  A Quasi-Analytical Method for Fluid Flow in a Multi-Inlet Collection Manifold , 2007 .

[15]  Asterios Gavriilidis,et al.  Flow Distribution in Different Microreactors Scale-Out Geometries and the Effect on Manufacturing Tolerances and Channel Blocking , 2004 .

[16]  H. Martin,et al.  Flow distribution and pressure drop in plate heat exchangers—II Z-type arrangement , 1984 .

[17]  Guohui Gan,et al.  Analytical solution of flow coefficients for a uniformly distributed porous channel , 2001 .

[18]  J. Galpin,et al.  Large Eddy Simulation of a thermal mixing tee in order to assess the thermal fatigue , 2011 .

[19]  J. Jung,et al.  Analysis of Unsteady Turbulent Triple Jet Flow with Temperature Difference , 2004 .

[20]  D. Legendre,et al.  Numerical Simulation for Two-Phase Flows in Fuel Cell Minichannels , 2011 .

[21]  Keith Scott,et al.  Pressure drop modelling for liquid feed direct methanol fuel cells: Part 1. Model development , 1999 .

[22]  S. Kær,et al.  Particle Image Velocimetry and Computational Fluid Dynamics Analysis of Fuel Cell Manifold , 2010 .

[23]  E. Sparrow,et al.  Effect of exit-port geometry on the performance of a flow distribution manifold , 2009 .

[24]  Stephen A. Solovitz,et al.  Manifold Design for Micro-Channel Cooling With Uniform Flow Distribution , 2011 .

[25]  Hoon-ki Choi,et al.  ICONE15-10130 ANALYSIS OF RESISTANCE EFFECT ON CORE FLOW DISTRIBUTION , 2007 .

[26]  Zhou Wei,et al.  Flow Distribution among Microchannels with Asymmetrical Manifolds , 2007, 2007 IEEE International Conference on Control and Automation.

[27]  J. Bae,et al.  Parallel Manifold Effects on the Heat and Mass Transfer Characteristics of Metal-Supported Solid Oxide Fuel Cell Stacks , 2011 .

[28]  O. Matar,et al.  Effects of Geometry, Flow Index, and Temperature on Flow Splitting , 2005 .

[29]  Hee Chun Lim,et al.  Pressure and flow distribution in internal gas manifolds of a fuel-cell stack , 2003 .

[30]  Kwan-Soo Lee,et al.  Flow Distribution in Manifold Using Modified Equal Pressure Method , 2009 .