Material Evaluation and Process Optimization of CNT-Coated Polymer Powders for Selective Laser Sintering

Multi-walled carbon nanotubes (CNTs) as nano-reinforcements were introduced to facilitate the laser sintering process and enhance the thermal and mechanical properties of polymeric composites. A dual experimental-theoretical method was proposed to evaluate the processability and predict the process parameters of newly developed CNT-coated polyamide 12 (CNTs/PA12) powders. The thermal conductivity, melt viscosity, phase transition and temperature-dependent density and heat capacity of PA12 and CNTs/PA12 powders were characterized for material evaluation. The composite powders exhibited improved heat conduction and heat absorption compared with virgin polymer powders, and the stable sintering range of composite powders was extended and found to be favourable for the sintering process. The microstructures of sintered composites revealed that the CNTs remained at the powder boundaries and formed network architectures, which instantaneously induced the significant enhancements in tensile strength, elongation at break and toughness without sacrificing tensile modulus.

[1]  Mo Song,et al.  Improving the mechanical properties of laser-sintered polyamide 12 through incorporation of carbon nanotubes , 2013 .

[2]  Jiangsha Meng,et al.  Structural Polymer-Based Carbon Nanotube Composite Fibers: Understanding the Processing–Structure–Performance Relationship , 2013, Materials.

[3]  S. Das,et al.  Processing and properties of glass bead particulate-filled functionally graded Nylon-11 composites produced by selective laser sintering , 2006 .

[4]  Mina Aliakbari,et al.  Additive Manufacturing: State-of-the-Art, Capabilities, and Sample Applications with Cost Analysis , 2012 .

[5]  David W. Rosen,et al.  Modeling effects of oxygen inhibition in mask‐based stereolithography , 2011 .

[6]  Dong Yol Yang,et al.  Improvement of spatial resolution in nano-stereolithography using radical quencher , 2006 .

[7]  Val A. Kagan,et al.  Relationship between Optical Properties and Optimized Processing Parameters for through-Transmission Laser Welding of Thermoplastics , 2004 .

[8]  I. Yadroitsava,et al.  Evaluation of residual stress in stainless steel 316L and Ti6Al4V samples produced by selective laser melting , 2015 .

[9]  Goonhee Lee.  Selective laser sintering of calcium phosphate materials for orthopedic implants , 1997 .

[10]  Chee Kai Chua,et al.  Thermal Influence of CNT on the Polyamide 12 Nanocomposite for Selective Laser Sintering , 2015, Molecules.

[11]  C. Yan,et al.  Investigation and development of large-scale equipment and high performance materials for powder bed laser fusion additive manufacturing , 2014 .

[12]  Chee Kai Chua,et al.  Effect of surface orientation on the tribological properties of laser sintered polyamide 12 , 2015 .

[13]  Kenan Song,et al.  Tailoring polyacrylonitrile interfacial morphological structure by crystallization in the presence of single-wall carbon nanotubes. , 2013, ACS applied materials & interfaces.

[14]  V. E. Beal,et al.  Microstructural and mechanical characterization of PA12/MWCNTs nanocomposite manufactured by selective laser sintering , 2011 .

[15]  Oana Ghita,et al.  Predicting processing parameters in high temperature laser sintering (HT-LS) from powder properties , 2016 .

[16]  K. Leong,et al.  Investigation on processing of ASTM A131 Eh36 high tensile strength steel using selective laser melting† , 2015 .

[17]  R. Hague,et al.  Laser sintering of polyamides and other polymers , 2012 .

[18]  M. Vincent,et al.  Influence of injection molding on the electrical properties of polyamide 12 filled with multi-walled carbon nanotubes , 2014 .

[19]  K. Zhou,et al.  Highly enhanced thermal conductivity of thermoplastic nanocomposites with a low mass fraction of MWCNTs by a facilitated latex approach , 2016 .

[20]  Mo Song,et al.  Influence of carbon nanotubes on the rheology and dynamic mechanical properties of polyamide-12 for laser sintering , 2014 .

[21]  L. Papadakis,et al.  A computational reduction model for appraising structural effects in selective laser melting manufacturing , 2014 .

[22]  Robert L. Danley.  New heat flux DSC measurement technique , 2002 .

[23]  C. Yan,et al.  Investigation into mechanical and microstructural properties of polypropylene manufactured by selective laser sintering in comparison with injection molding counterparts , 2015 .

[24]  Patrice Peyre,et al.  Experimental and numerical analysis of the selective laser sintering (SLS) of PA12 and PEKK semi-crystalline polymers , 2015 .

[25]  Vishal Francis,et al.  Experimental investigations on fused deposition modelling of polymer-layered silicate nanocomposite , 2016 .

[26]  Neil Hopkinson,et al.  Methods for quantifying the stable sintering region in laser sintered polyamide-12 , 2013 .

[27]  Gurunathan Saravana Kumar,et al.  An experimental and theoretical investigation of surface roughness of poly-jet printed parts , 2015 .

[28]  Chee Kai Chua,et al.  3D printing and additive manufacturing : principles and applications , 2015 .

[29]  J. Kruth,et al.  Characterization of polyamide powders for determination of laser sintering processability , 2016 .

[30]  Chee Kai Chua,et al.  3D printing by selective laser sintering of polypropylene feed channel spacers for spiral wound membrane modules for the water industry , 2016 .