Development of an Experimental Rig for Investigation of Higher Order Modes in Ducts

Continued progress to reduce fan noise emission from high bypass ratio engine ducts in aircraft increasingly relies on accurate description of the sound propagation in the duct. A project has been undertaken at NASA Langley Research Center to investigate the propagation of higher order modes in ducts with flow. This is a two-pronged approach, including development of analytic models (the subject of a separate paper) and installation of a laboratory-quality test rig. The purposes of the rig are to validate the analytical models and to evaluate novel duct acoustic liner concepts, both passive and active. The dimensions of the experimental rig test section scale to between 25% and 50% of the aft bypass ducts of most modern engines. The duct is of rectangular cross section so as to provide flexibility to design and fabricate test duct liner samples. The test section can accommodate flow paths that are straight through or offset from inlet to discharge, the latter design allowing investigation of the effect of curvature on sound propagation and duct liner performance. The maximum air flow rate through the duct is Mach 0.3. Sound in the duct is generated by an array of 16 high-intensity acoustic drivers. The signals to the loudspeaker array are generated by a multi-input/multi-output feedforward control system that has been developed for this project. The sound is sampled by arrays of flush-mounted microphones and a modal decomposition is performed at the frequency of sound generation. The data acquisition system consists of two arrays of flush-mounted microphones, one upstream of the test section and one downstream. The data are used to determine parameters such as the overall insertion loss of the test section treatment as well as the effect of the treatment on a modal basis such as mode scattering. The methodology used for modal decomposition is described, as is a description of the mode generation control system. Data are presented which demonstrate the performance of the controller to generate the desired mode while suppressing all other cut on modes in the duct.

[1]  R. J. Silcox,et al.  Experimental investigation of the radiation of sound from an unflanged duct and a bellmouth, including the flow effect , 1980 .

[2]  R. J. Silcox.  Experimental investigation of geometry and flow effects on acoustic radiation from duct inlets , 1983 .

[3]  L Padula Sharon,et al.  Optimization Strategies for Sensor and Actuator Placement , 1999 .

[4]  Carl H. Gerhold.  Determination of fan inlet duct mode structure using in‐duct microphone array measurement , 2001 .

[5]  P. Vaidya,et al.  The state of the art of duct acoustics , 1977 .

[6]  T. G. Sofrin,et al.  Modal propagation angles in a cylindrical duct with flow and their relation to sound radiation , 1979 .

[7]  Willie R. Watson,et al.  Comparison of Acoustic Impedance Eduction Techniques for Locally-Reacting Liners , 2003 .

[8]  Scott D. Sommerfeldt,et al.  Active Control of Low-Speed Fan Tonal Noise Using Actuators Mounted in Stator Vanes: Part 1 Control System Design and Implementation , 2003 .

[9]  P. Joppa.  An acoustic mode measurement technique , 1984 .

[10]  Stephen J. Elliott,et al.  Signal Processing for Active Control , 2000 .

[11]  Ricardo A. Burdisso,et al.  Time-Averaged Active Controller for Turbofan Engine Fan Noise Reduction , 1996 .

[12]  R H Thomas,et al.  A Mode Detection Method Using the Azimuthal Directivity of a Turbofan Model , 1999 .

[13]  A. V. Saule,et al.  Analysis of radiation patterns of interaction tones generated by inlet rods in the JT15D engine , 1979 .

[14]  Bruce N. Walker,et al.  Active Control of Low-Speed Fan Tonal Noise Using Actuators Mounted in Stator Vanes Part 2: Novel Error Sensing Concepts , 2003 .

[15]  W. R. Watson,et al.  Comparison of measured and calculated mode redistribution associated with spinning mode transmission through circumferentially segmented lined ducts , 1983 .

[16]  L. Homyak,et al.  Acoustic performance of inlet suppressors on an engine generating a single mode , 1981 .

[17]  Simon Haykin,et al.  Adaptive filter theory (2nd ed.) , 1991 .

[18]  D. L. Palumbo.  An operations manual for the Spinning Mode Synthesizer in the Langley Aircraft Noise Reduction Laboratory , 1981 .

[19]  W. R. Watson.  An evaluation of circumferentially segmented duct liners , 1983 .

[20]  R. P. Woodward,et al.  Tone Generation by Rotor-Downstream Strut Interaction , 1984 .

[21]  Audra E. Kosh,et al.  Linear Algebra and its Applications , 1992 .

[22]  Dinh Van Huynh,et al.  Algebra and Its Applications , 2006 .

[23]  Harold C. Lester,et al.  Sound Propagation Through a Variable Area Duct: Experiment and Theory , 1982 .

[24]  Carl H. Gerhold,et al.  Active Control of Fan-Generated Tone Noise , 1997 .

[25]  Willie R. Watson,et al.  Comparison of Two Waveguide Methods for Educing Liner Impedance in Grazing Flow , 2004 .

[26]  T. G. Sofrin,et al.  Axial Flow Compressor Noise Studies , 1962 .

[27]  Daniel L. Sutliff,et al.  Duct Mode Measurements on the TFE731-60 Full Scale Engine , 2002 .

[28]  R. Burdisso,et al.  Experiments on the active control of inlet noise from a turbofan jet engine using multiple circumferential control arrays , 1996 .

[29]  Stephen J. Elliott,et al.  A multiple error LMS algorithm and its application to the active control of sound and vibration , 1987, IEEE Trans. Acoust. Speech Signal Process..

[30]  Daniel L. Sutliff,et al.  Active Control of Low-Speed Fan Tonal Noise Using Actuators Mounted in Stator Vanes: Part III Results , 2003 .