Effect of Geological Structure on Flyrock Prediction in Construction Blasting

Blasting is sometimes inevitable in civil engineering work, to fragment the massive rock to enable excavation and leveling. In Minyak Beku, Batu Pahat also, blasting is implemented to fragment the rock mass, to reduce the in situ rock level to the required platform for a building construction. However, during blasting work, some rocks get an excessive amount of explosive energy and this energy may generate flyrock. An accident occurred on 15 July 2015 due to this phenomenon, in which one of the workers was killed and two other workers were seriously injured after being hit by the flyrock. The purpose of this study is to investigate the causes of the flyrock accidents through evaluation of rock mass geological structures. The discontinuities present on the rock face were analyzed, to study how they affected the projection and direction of the flyrock. Rock faces with lower mean joint spacing and larger apertures caused excessive flyrock. Based on the steoreonet analysis, it was found that slope failures also produced a significant effect on the direction, if the rock face failure lay in the critical zone area. Empirical models are often used to predict flyrock projection. In this study five empirical models are used to compare the incidents. It was found that none of the existing formulas could accurately predict flyrock distance. Analysis shows that the gap between predicted and actual flyrock can be reduced by including blast deign and geological conditions in forecasts. Analysis revealed only 69% of accuracy could be achieved if blast design is the only parameter to be considered in flyrock projection and the rest is influenced by the geological condition. Other causes of flyrock are discussed. Comparison of flyrock prediction with face bursting, cratering and rifling is carried out with recent prediction models.

[1]  A. K. Raina,et al.  Flyrock in Surface Mine Blasting: Understanding the Basics to Develop a Predictive Regime , 2015 .

[2]  Danial Jahed Armaghani,et al.  Evaluation and prediction of flyrock resulting from blasting operations using empirical and computational methods , 2015, Engineering with Computers.

[3]  Gento Mogi,et al.  Optimum delay interval design in delay blasting , 2000 .

[4]  G. L. Mowrey,et al.  Blasting injuries in surface mining with emphasis on flyrock and blast area security. , 2004, Journal of Safety Research.

[5]  Saša Stojadinović,et al.  Prediction of flyrock trajectories for forensic applications using ballistic flight equations , 2011 .

[6]  Danial Jahed Armaghani,et al.  Prediction of flyrock in boulder blasting by using artificial neural network , 2012 .

[7]  P. N. Calder,et al.  Flyrock prediction and control in surface mine blasting , 1994 .

[8]  T. N. Singh,et al.  Prediction of blast-induced flyrock in Indian limestone mines using neural networks , 2014 .

[9]  Danial Jahed Armaghani,et al.  Effect of geological structure and blasting practice in fly rock accident at Johor, Malaysia , 2016 .

[10]  A. Mishra,et al.  Flyrocks - Detection and Mitigation at Construction Site in Blasting Operation , 2012 .

[11]  C. J. Konya,et al.  Surface Blast Design , 1990 .

[12]  Giovanni Grasselli,et al.  ROCKTOPPLE: A spreadsheet-based program for probabilistic block-toppling analysis , 2010, Comput. Geosci..

[13]  Danial Jahed Armaghani,et al.  The effect of geological structure and powder factor in flyrock accident, Masai, Johor, Malaysia , 2013 .

[14]  S. Olofsson.  Applied Explosives Technology for Construction and Mining , 1988 .

[15]  Masoud Monjezi,et al.  Evaluation of effect of blast design parameters on flyrock using artificial neural networks , 2012, Neural Computing and Applications.

[16]  D. E. Siskind,et al.  Blasting accidents in mines, a 16-year summary , 1995 .

[17]  A. K. Raina,et al.  Flyrock danger zone demarcation in opencast mines: a risk based approach , 2011 .

[18]  G. R. Adhikari.  Studies on Flyrock at Limestone Quarries , 1999 .

[19]  Masoud Monjezi,et al.  Application of TOPSIS method for selecting the most appropriate blast design , 2010, Arabian Journal of Geosciences.

[20]  A. K. Raina,et al.  Flyrock in bench blasting: a comprehensive review , 2014, Bulletin of Engineering Geology and the Environment.

[21]  D. K. Ingram,et al.  A Summary of Fatal Accidents Due to Flyrock and Lack of Blast Area Security in Surface Mining, 1989 to 1999 , 1900 .

[22]  Sushil Bhandari,et al.  Engineering rock blasting operations , 1997 .

[23]  Mohammad Ataei,et al.  Development of an empirical model for predicting the effects of controllable blasting parameters on flyrock distance in surface mines , 2012 .

[24]  V. Kecojevic,et al.  Flyrock phenomena and area security in blasting-related accidents , 2005 .