Utilizing cable winding and industrial robots to facilitate the manufacturing of electric machines

Cable wound electric machines are used mainly for high voltage and direct-drive applications. They can be found in areas such as wind power, hydropower, wave power and high-voltage motors. Compared to conventional winding techniques, cable winding includes fewer manufacturing steps and is therefore likely to be better suited for automated production. Automation of the cable winding production step is a crucial task in order to lower the manufacturing costs of these machines. This article presents a production method using industrial robots for automation of cable winding of electric machine stators. The concept presented is validated through computer simulations and full-scale winding experiments, including a constructed robot-held cable feeder tool prototype. A cable wound linear stator section of an Uppsala University Wave Energy Converter and its winding process is used as a reference in this article. From this example, it is shown that considerable production cycle time and manufacturing cost savings can be anticipated compared to manual winding. The suggested automation method is very flexible. It can be used for the production of cable wound stators with different shapes and sizes, for different cable dimensions and with different winding patterns. Highlights? Utilizing cable winding in stators is likely to facilitate automated assembling. ? A robot automated manufacturing method for cable winding is presented. ? Computer simulations and prototype experiments validate the automation method. ? An Uppsala University Wave Energy Converter cable wound stator is used as reference. ? Automation method can be used for different stator designs and winding patterns.

[1]  Atsushi Konno,et al.  Robotized assembly of a wire harness in car production line , 2010, 2010 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[2]  D. W. Mumford.  In-slot stator winding of DC brushless motors , 2003, Proceedings: Electrical Insulation Conference and Electrical Manufacturing and Coil Winding Technology Conference (Cat. No.03CH37480).

[3]  W. D. Reed.  Self-bonding wire in automated motor assembly , 2003, Proceedings: Electrical Insulation Conference and Electrical Manufacturing and Coil Winding Technology Conference (Cat. No.03CH37480).

[4]  David P. Gravel.  Flexible robotic assembly efforts at Ford Motor Company IEEE/RSJ international conference on intelligent robots and systems , 2003, Proceedings 2003 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS 2003) (Cat. No.03CH37453).

[5]  Heping Chen,et al.  Toward robotizing powertrain assembly , 2008, 2008 7th World Congress on Intelligent Control and Automation.

[6]  Mats Leijon,et al.  A recent development in the electrical insulation systems of generators and transformers , 2001 .

[7]  Masaru Nakazawa,et al.  Study on high precision winding of toroidal coil and automation of its process , 2001, 2001 IEEE/ASME International Conference on Advanced Intelligent Mechatronics. Proceedings (Cat. No.01TH8556).

[8]  Atsushi Konno,et al.  Robotized assembly of a wire harness in car production line , 2010, 2010 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[9]  M. Savaghebi,et al.  Synchronous generator: past, present and future , 2007, AFRICON 2007.

[10]  Ayman M. El-Refaie,et al.  Fractional-Slot Concentrated-Windings Synchronous Permanent Magnet Machines: Opportunities and Challenges , 2010, IEEE Transactions on Industrial Electronics.

[11]  Christine Connolly.  Technology and applications of ABB RobotStudio , 2009, Ind. Robot.

[12]  Bijan Shirinzadeh,et al.  Robotic fibre placement process planning and control , 2000 .

[13]  Murray Khouri.  Revolution in the Wind , 1976 .

[14]  M. Leijon,et al.  Wave Energy from the North Sea: Experiences from the Lysekil Research Site , 2008 .

[15]  M. Leijon,et al.  Matching a Permanent Magnet Synchronous Generator to a Fixed Pitch Vertical Axis Turbine for Marine Current Energy Conversion , 2009, IEEE Journal of Oceanic Engineering.

[16]  P. Morreale.  Electric motor and generator manufacturing myths , 2007, 2007 Electrical Insulation Conference and Electrical Manufacturing Expo.

[17]  Hiroyuki Uchida,et al.  FANUC ‐ the planning and development of a highly advanced robotized production system for servo motors , 1998 .

[18]  Hans Bernhoff,et al.  Simulations and experiments on a 12 kW direct driven PM synchronous generator for wind power , 2008 .

[19]  H. Bergstrom,et al.  Assembly of generators with rated voltage higher than 100 kV , 2000, PowerCon 2000. 2000 International Conference on Power System Technology. Proceedings (Cat. No.00EX409).

[20]  Roger Dettmer.  The heart of a new machine , 1998 .

[21]  I.A. Metwally,et al.  Powerformers: A breakthrough of high-voltage power generators , 2008, IEEE Potentials.

[22]  Ferdinando Cannella,et al.  Automatic folding of cartons using a reconfigurable robotic system , 2011 .

[23]  J. Gamez Garcia,et al.  Industrial assembly of parts with dimensional variations. Case study: Assembling vehicle headlamps , 2011 .

[24]  Barrie Mecrow,et al.  Simplifying the manufacturing process for electrical machines , 2004 .

[25]  J. L. Thompson,et al.  Telecomms to the people : Glasgow leads the way , 2000 .

[26]  Nobuaki Miyake,et al.  New core structure and manufacturing method for high efficiency of permanent magnet motors , 2003, 38th IAS Annual Meeting on Conference Record of the Industry Applications Conference, 2003..

[27]  Kohji Haga,et al.  Design and Manufacturing Technology of Fuji Electric’s Large-Capacity, Air-Cooled Turbine Generator , 2007 .

[28]  Mats Leijon,et al.  Study of a longitudinal flux permanent magnet linear generator for wave energy converters , 2006 .

[29]  Sture Lindahl,et al.  Powerformer(R): a giant step in power plant engineering , 1999, IEEE International Electric Machines and Drives Conference. IEMDC'99. Proceedings (Cat. No.99EX272).

[30]  Kazushi Sanada,et al.  Stator-core structure and winding technology for EPS motors , 2011 .

[31]  C. Parkegren,et al.  Powerformer/sup TM/-the prototype and beyond , 2000, 2000 IEEE Power Engineering Society Winter Meeting. Conference Proceedings (Cat. No.00CH37077).

[32]  John Mortimer.  BMW lifts robot total to 500 at Plant Oxford , 2008 .

[33]  C. Parkegren,et al.  Powerformer/sup TM/-experiences from the application of extruded solid dielectric cables in the stator winding of rotating machines , 2000, 2000 IEEE Power Engineering Society Winter Meeting. Conference Proceedings (Cat. No.00CH37077).

[34]  John Mortimer.  Jaguar lifts XF robot total to 179 , 2009, Ind. Robot.

[35]  W. S. Newman,et al.  Flexible robotic assembly efforts at Ford Motor Company , 2001, Proceeding of the 2001 IEEE International Symposium on Intelligent Control (ISIC '01) (Cat. No.01CH37206).

[36]  A.G. Jack,et al.  Permanent magnet machines with powdered iron cores and pre-pressed windings , 1999, Conference Record of the 1999 IEEE Industry Applications Conference. Thirty-Forth IAS Annual Meeting (Cat. No.99CH36370).