Additive manufacturing-enabled shape transformations via FFF 4D printing

<jats:p><jats:fig position="anchor"><jats:graphic xmlns:xlink="http://www.w3.org/1999/xlink" orientation="portrait" mime-subtype="jpeg" mimetype="image" position="float" xlink:type="simple" xlink:href="S0884291418003977_figAb" /></jats:fig></jats:p>

[1]  Jie Zhang,et al.  Numerical investigation of the influence of process conditions on the temperature variation in fused deposition modeling , 2017 .

[2]  H. N. Bhargaw,et al.  Improved recovery stress in multi-walled-carbon-nanotubes reinforced polyurethane , 2015 .

[3]  E. García-Plaza,et al.  Additive manufacturing of PLA structures using fused deposition modelling: Effect of process parameters on mechanical properties and their optimal selection , 2017 .

[4]  Skylar Tibbits,et al.  4D Printing: Multi‐Material Shape Change , 2014 .

[5]  R. Velmurugan,et al.  Reversible plasticity shape memory effect in carbon nanotubes reinforced epoxy nanocomposites , 2016 .

[6]  Thao D. Nguyen,et al.  A thermoviscoelastic model for amorphous shape memory polymers: Incorporating structural and stress relaxation , 2008 .

[7]  Dong Yan,et al.  Pattern Transformation of Heat-Shrinkable Polymer by Three-Dimensional (3D) Printing Technique , 2015, Scientific Reports.

[8]  W. Cantwell,et al.  Performance of biocompatible PEEK processed by fused deposition additive manufacturing , 2018 .

[9]  Richard S. Trask,et al.  An experimental demonstration of effective Curved Layer Fused Filament Fabrication utilising a parallel deposition robot , 2015 .

[10]  Wesley J. Cantwell,et al.  Additively manufactured cylindrical systems with stiffness-tailored interface: Modeling and experiments , 2018, International Journal of Solids and Structures.

[11]  M. A. Khan,et al.  Performance enhancement of tubular multilayers via compliance-tailoring: 3D printing, testing and modeling , 2018 .

[12]  P. Upadhyaya,et al.  Hyperelastic strain measurements and constitutive parameters identification of 3D printed soft polymers by image processing , 2016 .

[13]  Caterina Casavola,et al.  Residual stress measurement in Fused Deposition Modelling parts , 2017 .

[14]  Glaucio H. Paulino,et al.  Programmable Deployment of Tensegrity Structures by Stimulus-Responsive Polymers , 2017, Scientific Reports.

[15]  Jordi Llumà,et al.  Mechanical property characterization and simulation of fused deposition modeling Polycarbonate parts , 2015 .

[16]  Wei Xu,et al.  Thermomechanical behavior of thermoset shape memory polymer programmed by cold-compression: Testing and constitutive modeling , 2011 .

[17]  Yiping Liu,et al.  Thermomechanics of shape memory polymers: Uniaxial experiments and constitutive modeling , 2006 .

[18]  Yong He,et al.  Modeling and process planning for curved layer fused deposition , 2017 .

[19]  Brian N. Turner,et al.  A review of melt extrusion additive manufacturing processes: II. Materials, dimensional accuracy, and surface roughness , 2015 .

[20]  Martin L. Dunn,et al.  Active origami by 4D printing , 2014 .

[21]  Jun Ni,et al.  A review of 4D printing , 2017 .

[22]  Hui Wang,et al.  Additive manufacturing of carbon fiber-reinforced plastic composites using fused deposition modeling: Effects of process parameters on tensile properties , 2017 .

[23]  D. Karalekas,et al.  In-situ monitoring of strain and temperature distributions during fused deposition modeling process , 2016 .

[24]  A. K. Sood,et al.  Parametric appraisal of mechanical property of fused deposition modelling processed parts , 2010 .

[25]  R. Velmurugan,et al.  Reversible plasticity shape memory effect in epoxy/CNT nanocomposites - A theoretical study , 2017 .

[26]  A. K. Sood,et al.  Improving dimensional accuracy of Fused Deposition Modelling processed part using grey Taguchi method , 2009 .

[27]  Quan Zhang,et al.  Smart three-dimensional lightweight structure triggered from a thin composite sheet via 3D printing technique , 2016, Scientific Reports.

[28]  J. Xi,et al.  A model research for prototype warp deformation in the FDM process , 2007 .

[29]  B. Wardle,et al.  Strength and Performance Enhancement of Bonded Joints by Spatial Tailoring of Adhesive Compliance via 3D Printing. , 2017, ACS applied materials & interfaces.

[30]  R. Velmurugan,et al.  Free, partial, and fully constrained recovery analysis of cold-programmed shape memory epoxy/carbon nanotube nanocomposites: Experiments and predictions , 2018 .

[31]  B. Wardle,et al.  Stress Reduction of 3D Printed Compliance‐Tailored Multilayers , 2018 .

[32]  Lallit Anand,et al.  Thermally actuated shape-memory polymers: Experiments, theory, and numerical simulations , 2010 .

[33]  B. Wardle,et al.  Enhanced Bonding via Additive Manufacturing‐Enabled Surface Tailoring of 3D Printed Continuous‐Fiber Composites , 2018, Advanced Engineering Materials.

[34]  A. R. Damanpack,et al.  Adaptive metamaterials by functionally graded 4D printing , 2017 .

[35]  Martin L. Dunn,et al.  Sequential Self-Folding Structures by 3D Printed Digital Shape Memory Polymers , 2015, Scientific Reports.

[36]  M. Boyce,et al.  A three-dimensional constitutive model for the large stretch behavior of rubber elastic materials , 1993 .

[37]  Wei-Hsin Liao,et al.  Increasing dimension of structures by 4D printing shape memory polymers via fused deposition modeling , 2017 .

[38]  P. Wright,et al.  Anisotropic material properties of fused deposition modeling ABS , 2002 .

[39]  B. Wardle,et al.  Strength and Performance Enhancement of Multilayers by Spatial Tailoring of Adherend Compliance and Morphology via Multimaterial Jetting Additive Manufacturing , 2018, Scientific Reports.

[40]  M. Boyce,et al.  On the kinematics of finite strain plasticity , 1989 .

[41]  Antreas Kantaros,et al.  Fiber Bragg grating based investigation of residual strains in ABS parts fabricated by fused deposition modeling process , 2013 .