CONWIP ASSEMBLY WITH DETERMINISTIC PROCESSING AND RANDOM OUTAGES

We develop structural results and an approximation for the throughput of an assembly system fed by multi-station fabrication lines where releases are governed by the CONWIP protocol and all machines have deterministic processing times but are subject to random outages. This formulation is motivated by a printed circuit board manufacturing process. We demonstrate that while throughput of such systems is nondecreasing in machine speed, there are cases where throughput declines when mean time between failures (MTBF) increases or mean time to repair (MTTR) decreases. Using the concept of "deterministic steady state," which describes the behavior of the system in die absence of failures, we derive a simple, closed-form approximation for throughput. Comparisons with simulation show that this approximation is robust over a wide range of conditions. Finally, we observe that throughput tends to be higher when the bottleneck is located in fabrication rather than assembly.

[1]  J. A. Buzacott,et al.  The role of inventory banks in flow-line production systems , 1971 .

[2]  J. Harrison.  Assembly-like queues , 1973, Journal of Applied Probability.

[3]  J. Wijngaard.  The Effect of Interstage Buffer Storage on the Output of Two Unreliable Production Units in Series, with Different Production Rates , 1979 .

[4]  Mostafa H. Ammar,et al.  Modelling and analysis of unreliable manufacturing assembly networks with finite storages , 1980 .

[5]  Stanley B. Gershwin,et al.  An algorithm for the computer control of a flexible manufacturing system , 1983 .

[6]  R. Akella,et al.  Optimal control of production rate in a failure prone manufacturing system , 1985, 1985 24th IEEE Conference on Decision and Control.

[7]  E. H. Lipper,et al.  Assembly-like queues with finite capacity: Bounds, asymptotics and approximations , 1986, Queueing Syst. Theory Appl..

[8]  U. Narayan Bhat,et al.  Finite capacity assembly-like queues , 1986, Queueing Syst. Theory Appl..

[9]  Flavio Bonomi,et al.  An approximate analysis for a class of assembly-like queues , 1987, Queueing Syst. Theory Appl..

[10]  Rajan Suri,et al.  Rough-cut modeling: an alternative to simulation , 1987 .

[11]  A. Sharifnia,et al.  Production control of a manufacturing system with multiple machine states , 1988 .

[12]  Wolfgang Bechte.  Theory and practice of load-oriented manufacturing control , 1988 .

[13]  Steven A. Melnyk,et al.  Order review/release: research issues and perspectives , 1989 .

[14]  Bryan L. Deuermeyer,et al.  Discrete Simulation: Fundamentals and Microcomputer Support , 1989 .

[15]  W. J. Hopp,et al.  Bounds and heuristics for assembly-like queues , 1989, Queueing Syst. Theory Appl..

[16]  David L. Woodruff,et al.  CONWIP: a pull alternative to kanban , 1990 .

[17]  Lawrence M. Wein,et al.  Scheduling Networks of Queues: Heavy Traffic Analysis of a Two-Station Closed Network , 1990, Oper. Res..

[18]  Wallace J. Hopp,et al.  Throughput of a constant work in process manufacturing line subject to failures , 1991 .

[19]  Michael A. Zazanis,et al.  Push and Pull Production Systems: Issues and Comparisons , 1992, Oper. Res..

[20]  Wallace J. Hopp,et al.  Characterizing the Output Process of a CONWIP Line with Deterministic Processing and Random Outages , 1993 .

[21]  Stephen G. Powell,et al.  Optimal Allocation of Work in Assembly Systems , 1993 .

[22]  John B. Kidd,et al.  Toyota Production System , 1993 .