DRAPE OPTIMISATION IN WOVEN COMPOSITE MANUFACTURING

This paper addresses the optimisation of forming in manufacturing of composites. A simplified finite element model of draping is developed and implemented. The model incorporates the non-linear shear response of textiles and wrinkling due to buckling of tows. The model is validated against experimental results and it is concluded that it reproduces successfully the most important features of the process. The simple character of the model results in low computational times that allow its use within an optimisation procedure. A genetic algorithm is used to solve the optimisation problem of minimising the wrinkling in the formed component by selecting a suitable holding force distribution. The effect of regularisation is investigated and the L-curve is used to select a regularisation parameter value. Optimised designs resulting from the inversion procedure have significantly lower wrinkling than uniform holding force profiles, while regularisation allows force gradients to be kept relatively low so that suggested process designs are feasible.

[1]  Suresh G. Advani,et al.  Simultaneous gate and vent location optimization in liquid composite molding processes , 2004 .

[2]  F. Van Der Weeën,et al.  Algorithms for draping fabrics on doubly‐curved surfaces , 1991 .

[3]  John M. Hedgepeth,et al.  Finite element analysis of partly wrinkled membranes , 1985 .

[4]  Constantina Lekakou,et al.  Processing of Composites: Simulations of the Draping of Fabrics with Updated Material Behaviour Law , 2001 .

[5]  Dianne P. O'Leary,et al.  The Use of the L-Curve in the Regularization of Discrete Ill-Posed Problems , 1993, SIAM J. Sci. Comput..

[6]  Philippe H. Geubelle,et al.  Dimensional Accuracy of Thermoset Composites: Shape Optimization , 2002 .

[7]  Jean Louis Billoet,et al.  Mechanical and numerical modelling of composite manufacturing processes deep-drawing and laying-up of thin pre-impregnated woven fabrics , 2001 .

[8]  Prasad Potluri,et al.  Comprehensive drape modelling for moulding 3D textile preforms , 2001 .

[9]  A. Beris,et al.  Thick-Sectioned RTM Composite Manufacturing, Part II. Robust Cure Cycle Optimization and Control , 2002 .

[10]  S. Sharma,et al.  A simplified finite element model for draping of woven material , 2004 .

[11]  A. Hammami,et al.  Prediction of fibre orientation and net shape definition of complex composite parts , 1996 .

[12]  Anthony K. Pickett,et al.  An explicit finite element solution for the forming prediction of continuous fibre-reinforced thermoplastic sheets , 1995 .

[13]  Ben Wang,et al.  Integrated Product and Process Design for Resin Transfer Molded Parts , 1998 .

[14]  B. K. Fink,et al.  A Real-Coded Hybrid Genetic Algorithm to Determine Optimal Resin Injection Locations in the Resin Transfer Molding Process , 2003 .

[15]  Andrew C. Long,et al.  A constituent-based predictive approach to modelling the rheology of viscous textile composites , 2004 .

[16]  Dorothea Heiss-Czedik,et al.  An Introduction to Genetic Algorithms. , 1997, Artificial Life.

[17]  Suresh G. Advani,et al.  Investigation of draping and its effects on the mold filling process during manufacturing of a compound curved composite part , 1997 .

[18]  Ivana K. Partridge,et al.  Inverse heat transfer for optimization and on-line thermal properties estimation in composites curing , 2004 .

[19]  N. S. Mera,et al.  A multi-population genetic algorithm approach for solving ill-posed problems , 2004 .

[20]  Israel Herszberg,et al.  The shear properties of woven carbon fabric , 1999 .

[21]  Andrew C. Long,et al.  Shear characterisation of viscous woven textile composites: a comparison between picture frame and bias extension experiments , 2004 .