Optimization of Abrasive Powder Mixed EDM of Aluminum Matrix Composites with Multiple Responses Using Gray Relational Analysis

Abrasive powder-mixed electrical discharge machining (APM-EDM), a hybrid manufacturing process involving the use of a dielectric fluid mixed with abrasive powder, combines the benefits of mechanical and thermal interactions. The aim of this article is to use a new approach of performance evaluation, gray relational analysis (GRA), to evaluate the effectiveness of optimizing multiple performance characteristics of APM-EDM of 6061Al/Al2O3p/20p aluminum matrix composites (AMCs). The considered process parameter includes the seven control factors namely pulse current (A), pulse ON time (μs), duty cycle (%), gap voltage (V), time interval of tool lift (s), abrasive powder concentration (g/L), abrasive particle size (μm), and a noise factor, aspect ratio (shape of tool electrode). The combination of L18 (21 × 37) orthogonal array design of experiment with GRA enables to determine the optimal parameters for multiple responses. GRA is used to obtain a single performance index, gray relational grade through gray relational coefficient to optimize the APM-EDM process with lower tool wear rate, surface roughness, and higher material removal rate. In addition, analysis of variance (ANOVA) for the GRC is also utilized.

[1]  C. L. Lin,et al.  Optimisation of the EDM Process Based on the Orthogonal Array with Fuzzy Logic and Grey Relational Analysis Method , 2002 .

[2]  J. L Lin,et al.  The use of the orthogonal array with grey relational analysis to optimize the electrical discharge machining process with multiple performance characteristics , 2002 .

[3]  Ranjit K. Roy,et al.  Design of Experiments Using The Taguchi Approach: 16 Steps to Product and Process Improvement , 2001 .

[4]  J. Deng,et al.  Introduction to Grey system theory , 1989 .

[5]  B. Yan,et al.  Study of added powder in kerosene for the micro-slit machining of titanium alloy using electro-discharge machining , 2000 .

[6]  Y. Wong,et al.  Near-mirror-finish phenomenon in EDM using powder-mixed dielectric , 1998 .

[7]  Tzou-Chi Huang,et al.  GREY RELATIONAL ANALYSIS OF DRIED ROSELLE (HIBISCUS SABDARIFFA L.) , 2005 .

[8]  K. Chawla,et al.  Metal Matrix Composites , 2006 .

[9]  Farghalli A. Mohamed,et al.  Particulate reinforced metal matrix composites — a review , 1991, Journal of Materials Science.

[10]  Quan Ming,et al.  Powder-suspension dielectric fluid for EDM , 1995 .

[11]  N. Mohri,et al.  Accretion of titanium carbide by electrical discharge machining with powder suspended in working fluid , 2001 .

[12]  Xue-Rui Tan,et al.  Applications of gray relational analysis in gastroenterology. , 2005, World journal of gastroenterology.

[13]  Sachin Maheshwari,et al.  Optimisation of multiperformance characteristics in electric discharge machining of Aluminium Matrix Composites (AMCs) using Taguchi DOE methodology , 2007, Int. J. Manuf. Res..

[14]  K. Chiang,et al.  Optimization of the WEDM process of particle-reinforced material with multiple performance characteristics using grey relational analysis , 2006 .

[15]  Ji-Liang Doong,et al.  Optimization of the injection molding process of short glass fiber reinforced polycarbonate composites using grey relational analysis , 2000 .

[16]  Bruce Boardman,et al.  Metal matrix composites : an opportunity for the off-highway industry , 1990 .

[17]  W. Zhao,et al.  The application of research on powder mixed EDM in rough machining , 2002 .

[18]  L. Dabrowski,et al.  Study of electrical discharge machining using powder-suspended working media , 2003 .

[19]  H. Narumiya.  EDM by powder suspended working fluid , 1989 .

[20]  Aloke Dey,et al.  Experimental results and analysis for Electrical Discharge Machining (EDM) of aluminium metal matrix composites with powder-mixed dielectric: Lenth's method , 2010, Int. J. Manuf. Technol. Manag..

[21]  C. Fung.  Manufacturing process optimization for wear property of fiber-reinforced polybutylene terephthalate composites with grey relational analysis , 2003 .

[22]  N Tosun,et al.  Determination of optimum parameters for multi-performance characteristics in drilling by using grey relational analysis , 2006 .

[23]  D. Aspinwall,et al.  Electrical discharge surface alloying , 2004 .

[24]  Deng Ju-Long,et al.  Control problems of grey systems , 1982 .

[25]  Y. Uno,et al.  Surface Integrity in EDM of Aluminum Bronze with Nickel Powder Mixed Fluid , 1998 .

[26]  谭学瑞,et al.  GREY RELATIONAL ANALYSIS: A NEW STATISTICAL METHOD OF MULTIFACTORIAL ANALYSIS IN MEDICINE , 1997 .

[27]  M. L. Jeswani,et al.  Effect of the addition of graphite powder to kerosene used as the dielectric fluid in electrical discharge machining , 1981 .

[28]  Can Çoğun,et al.  EFFECT OF POWDER MIXED DIELECTRIC ON MACHINING PERFORMANCE IN ELECTRIC DISCHARGE MACHINING (EDM) , 2005 .

[29]  A. Erden,et al.  Role of Impurities in Electric Discharge Machining , 1981 .

[30]  Hu Wenbin,et al.  Building thermal process analysis with grey system method , 2002 .

[31]  E. Henriques,et al.  Influence of silicon powder-mixed dielectric on conventional electrical discharge machining , 2003 .

[32]  R. Fisher.  Statistical methods for research workers , 1927, Protoplasma.

[33]  Yunn-Shiuan Liao,et al.  Optimization of machining parameters of Wire-EDM based on Grey relational and statistical analyses , 2003 .

[34]  Bobby Schmidt,et al.  Fuzzy math , 2001 .

[35]  C. L. Lin,et al.  The use of grey-fuzzy logic for the optimization of the manufacturing process , 2005 .

[36]  F. Müller,et al.  Non-conventional machining of particle reinforced metal matrix composite , 2000 .

[37]  Shih-Cheng Hu,et al.  Design and evaluation of a minienvironment for semiconductor manufacture processes , 2002 .

[38]  Meng Lu,et al.  Modelling and evaluation of the effects of traffic safety measures Comparative analysis of driving assistance systems and road infrastructure , 2007 .

[39]  Akira Okada,et al.  Surface Generation Mechanism in Electrical Discharge Machining with Silicon Powder Mixed Fluid , 1995 .

[40]  Yih-fong Tzeng,et al.  Effects of Powder Characteristics on Electrodischarge Machining Efficiency , 2001 .

[41]  Madhan Shridhar Phadke,et al.  Quality Engineering Using Robust Design , 1989 .