Selective laser melting of AlSi10 Mg: Influence of process parameters on Mg2Si precipitation and Si spheroidization

[1]  R. Willens,et al.  DEFECTS IN ALUMINUM QUENCHED FROM THE LIQUID STATE. Technical Report No. 15 , 1963 .

[2]  T. H. Keijser,et al.  On precipitation in rapidly solidified aluminium-silicon alloys , 1983 .

[3]  E. Mittemeijer,et al.  Precipitation of silicon in aluminum-silicon: A calorimetric analysis of liquid-quenched and solid- quenched alloys , 1989 .

[4]  S. M. Allen,et al.  A calorimetric study of precipitation in commercial aluminium alloy 6061 , 1991 .

[5]  D. V. Ragone,et al.  Thermodynamics of materials , 1995 .

[6]  Kiyomichi Nakai,et al.  Precipitation and dissolution reactions in a 6061 Aluminum Alloy , 2000 .

[7]  APPROACHES TO PROCESSING METALS AND CERAMICS THROUGH THE LASER SCANNING OF POWDER BEDS - A REVIEW , 2001 .

[8]  K. Osakada,et al.  Rapid Manufacturing of Metal Components by Laser Forming , 2006 .

[9]  Jan Bültmann,et al.  High Power Selective Laser Melting (HP SLM) of Aluminum Parts , 2011 .

[10]  M. Daoudi,et al.  DSC study of the kinetic parameters of the metastable phases formation during non-isothermal annealing of an Al–Si–Mg alloy , 2011 .

[11]  Michael Schmidt,et al.  New Developments of Laser Processing Aluminium Alloys via Additive Manufacturing Technique , 2011 .

[12]  E. Brandl,et al.  Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior , 2012 .

[13]  J. Kruth,et al.  Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder , 2013 .

[14]  I. Ashcroft,et al.  Reducing porosity in AlSi10Mg parts processed by selective laser melting , 2014 .

[15]  Chandrika Kamath,et al.  Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing , 2014 .

[16]  E. O. Olakanmi,et al.  A review on selective laser sintering/melting (SLS/SLM) of aluminium alloy powders: Processing, microstructure, and properties , 2015 .

[17]  R. Poprawe,et al.  Selective laser melting of aluminum die-cast alloy—Correlations between process parameters, solidification conditions, and resulting mechanical properties , 2015 .

[18]  Wei Wang,et al.  Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development , 2015, Materials & Design (1980-2015).

[19]  Chee Kai Chua,et al.  Phase analysis and microstructure characterisation of AlSi10Mg parts produced by Selective Laser Melting , 2015 .

[20]  Zhaohui Huang,et al.  A selective laser melting and solution heat treatment refined Al-12Si alloy with a controllable ultrafine eutectic microstructure and 25% tensile ductility , 2015 .

[21]  Xinhua Wu,et al.  The influence of processing parameters on aluminium alloy A357 manufactured by Selective Laser Melting , 2016 .

[22]  Comparison study of numerical analysis for heat transfer and fluid flow under two different laser scan pattern during selective laser melting , 2016 .

[23]  T. Nakamoto,et al.  Microstructures and mechanical properties of A356 (AlSi7Mg0.3) aluminum alloy fabricated by selective laser melting , 2016 .

[24]  Hongwei Hu,et al.  Numerical analysis of heat transfer during multi-layer selective laser melting of AlSi10Mg , 2016 .

[25]  Properties of Aluminium Alloys Produced by Selective Laser Melting , 2016 .

[26]  Zhiheng Hu,et al.  Selective laser melting of high strength Al–Cu–Mg alloys: Processing, microstructure and mechanical properties , 2016 .

[27]  N. Takata,et al.  Change in microstructure of selectively laser melted AlSi10Mg alloy with heat treatments , 2017 .

[28]  Xueping Ding,et al.  Heat transfer and fluid flow of molten pool during selective laser melting of AlSi10Mg powder: Simulation and experiment , 2017 .

[29]  I. Ashcroft,et al.  Selective laser melting of aluminum alloys , 2017 .

[30]  Lin-zhi Wang,et al.  Numerical analysis of residual stress evolution of AlSi10Mg manufactured by selective laser melting , 2017 .

[31]  E. Atzeni,et al.  History of residual stresses during the production phases of AlSi10Mg parts processed by powder bed additive manufacturing technology , 2017 .

[32]  J. Fiocchi,et al.  Effect of ball milling on the ageing response of Al2618 composites reinforced with SiC and oxide nanoparticles , 2017 .

[33]  Quang-Cuong Pham,et al.  Selective laser melting of AlSi10Mg: Effects of scan direction, part placement and inert gas flow velocity on tensile strength , 2017 .

[34]  Sen Wang,et al.  Experimental investigation on densification behavior and surface roughness of AlSi10Mg powders produced by selective laser melting , 2017 .

[35]  D. Tomus,et al.  Defect, Microstructure, and Mechanical Property of Ti-6Al-4V Alloy Fabricated by High-Power Selective Laser Melting , 2017 .

[36]  J. Schoenung,et al.  On the limitations of Volumetric Energy Density as a design parameter for Selective Laser Melting , 2017 .

[37]  Carlo Alberto Biffi,et al.  Low temperature annealing dedicated to AlSi10Mg selective laser melting products , 2017 .

[38]  F. Calignano.  Investigation of the accuracy and roughness in the laser powder bed fusion process , 2018 .

[39]  Lai‐Chang Zhang,et al.  Gradient in microstructure and mechanical property of selective laser melted AlSi10Mg , 2018 .

[40]  D. Manfredi,et al.  A comparison of Selective Laser Melting with bulk rapid solidification of AlSi10Mg alloy , 2018 .