Influence of high power 405 nm multi-mode and single-mode diode laser light on the long-term stability of fused silica fibers

As the demand for high power fiber-coupled violet laser systems increases existing problems remain. The typical power of commercially available diode lasers around 400 nm is in the order of 100 to 300 mW, depending on the type of laser. But in combination with the small core of single-mode fibers reduced spot sizes are needed for good coupling efficiencies, leading to power densities in the MW/cm2 range. We investigated the influence of 405 nm laser light irradiation on different fused silica fibers and differently treated end-faces. The effect of glued-and-polished, cleaved-and-clamped and of cleaved-and-fusion-arc-treated fiber end-faces on the damage rate and behavior are presented. In addition, effects in the deep ultra-violet were determined spectrally using newest spectrometer technology, allowing the measurement of color centers around 200 nm in small core fibers. Periodic surface structures were found on the proximal end-faces and were investigated concerning generation control parameters and composition. The used fiber types range from low-mode fiber to single-mode and polarization-maintaining fiber. For this investigation 405 nm single-mode or multi-mode diode lasers with 150 mW or 300 mW, respectively, were employed.

[1]  Florenta Costache,et al.  Self-organized surface nanostructuring by femtosecond laser processing , 2006 .

[2]  Philippe M. Fauchet,et al.  Observations of higher-order laser-induced surface ripples on 〈111〉 germanium , 1983 .

[3]  Karl-Friedrich Klein,et al.  High-OH fibers with higher stability in the UV-region , 2006, SPIE BiOS.

[4]  Kenneth T. V. Grattan,et al.  Lifetime prediction for 405-nm single-mode delivery systems for therapeutic laser applications , 2012, Other Conferences.

[5]  J. Reif,et al.  High power laser interaction with the surface of wide bandgap materials , 1989 .

[6]  Karl-Friedrich Klein,et al.  Performance of low mode and single mode optical fibers for high peak power 355 nm laser radiation , 2011, BiOS.

[7]  Michael Bestehorn,et al.  Formation of self-organized regular nanostructures upon femtosecond laser ablation , 2004, International Symposium on Laser Precision Microfabrication.

[8]  Florenta Costache,et al.  Control parameters in pattern formation upon femtosecond laser ablation , 2007 .

[9]  Paul W. Levy,et al.  Radiation effects in glass and other materials , 1962 .

[10]  Preston,et al.  Pattern formation during laser melting of silicon. , 1989, Physical review. B, Condensed matter.

[11]  M. Birnbaum.  Semiconductor Surface Damage Produced by Ruby Lasers , 1965 .

[12]  A Peled,et al.  Simulation of thin film growth visualization in photodeposition , 2000 .

[13]  Hartmut S. Leipner,et al.  Long-time feedback in self-organized nanostructures formation upon multipulse femtosecond laser ablation , 2010, LASE.

[14]  Masud Mansuripur,et al.  The Optics of Semiconductor Diode Lasers , 2002 .

[15]  E. J. Friebele,et al.  Drawing‐induced defect centers in a fused silica core fiber , 1976 .

[16]  Fritz Keilmann,et al.  Periodic surface structures frozen into CO2 laser-melted quartz , 1982 .

[17]  T. Makimoto,et al.  Analysis of splice loss in single-mode fibres using a Gaussian field approximation , 1979 .

[18]  Karl-Friedrich Klein,et al.  UV fibers for applications below 200 nm , 2001, SPIE BiOS.

[19]  Avinashi Kapoor,et al.  Recrystallization of germanium surfaces by femtosecond laser pulses , 2003 .

[20]  Florenta Costache,et al.  Self-organized pattern formation upon femtosecond laser ablation by circularly polarized light , 2006 .

[21]  Juergen Reif,et al.  Femtosecond laser ablation from dielectric materials: Comparison to arc discharge erosion , 1999 .

[22]  Tong Sun,et al.  Characterization of UV single-mode and low-mode fibers , 2010, BiOS.

[23]  John E. Sipe,et al.  Laser-Induced Periodic Surface Structure on Solids: A Universal Phenomenon , 1982 .