Aerodynamic Loss for a Turbine Blade With Endwall Leakage Features and Contouring

Secondary flows near the endwall of a turbine blade contribute to a loss in aerodynamic performance in the engine. Further reductions in performance occur when the secondary flows interact with leakage flow from necessary clearance features, such as the clearance gap between the blade rotor and an upstream stator or gaps between adjacent blade platforms. Non-axisymmetric endwall contouring has been shown to reduce the strength of secondary flows near the endwall, but relatively little research has been done to test the sensitivity of the contouring to the endwall leakage features. This paper describes aerodynamic measurements taken downstream of a cascade with representative leakage features. In general, upstream leakage flow with swirl relative to the blade increased aerodynamic loss, relative to leakage that was matched to the blade wheelspeed. Non-axisymmetric contouring for an endwall without a platform gap reduced underturning of the flow but had no effect on overall loss, relative to a flat endwall without a gap. A contoured endwall with a platform gap had 12% higher mixed-out loss than a contoured endwall without a gap.Copyright © 2013 by ASME

[1]  John D. Denton,et al.  The Interaction of Turbine Inter-Platform Leakage Flow With the Mainstream Flow , 2005 .

[2]  Raúl Vázquez,et al.  The Effect of Reynolds and Mach Number on End-Wall Profiling Performance , 2010 .

[3]  Peter Jeschke,et al.  Numerical and Experimental Analysis of the Effects of Non-Axisymmetric Contoured Stator Endwalls in an Axial Turbine , 2010 .

[4]  John D. Denton,et al.  The Effect of Stator-Rotor Hub Sealing Flow on the Mainstream Aerodynamics of a Turbine , 2006 .

[5]  Antonio Giovanni Perdichizzi.  Mach Number Effects on Secondary Flow Development Downstream of a Turbine Cascade , 1990 .

[6]  Steen A. Sjolander,et al.  Measurements of Secondary Losses in a Turbine Cascade With the Implementation of Nonaxisymmetric Endwall Contouring , 2008 .

[7]  Howard P. Hodson,et al.  Aerodynamic Aspects of Endwall Film-Cooling , 1996 .

[8]  Howard P. Hodson,et al.  Aerothermal Impact of the Interaction Between Hub Leakage and Mainstream Flows in Highly-Loaded High Pressure Turbine Blades , 2013 .

[9]  Karen A. Thole,et al.  ENDWALL HEAT TRANSFER FOR A TURBINE BLADE WITH AN UPSTREAM CAVITY AND RIM SEAL LEAKAGE , 2013 .

[10]  Steen A. Sjolander,et al.  Application of Non-Axisymmetric Endwall Contouring to Conventional and High-Lift Turbine Airfoils , 2007 .

[11]  D. G. Gregory-Smith,et al.  Growth of Secondary Losses and Vorticity in an Axial Turbine Cascade , 1988 .

[12]  John D. Denton,et al.  Reducing the Perfomance Penalty Due to Turbine Inter-Platform Gaps , 2006 .

[13]  Karen A. Thole,et al.  Effect of Mach Number on Secondary Flow Characteristics , 2000 .

[14]  Santosh Abraham,et al.  Effect of Endwall Contouring on a Transonic Turbine Blade Passage: Part 1—Aerodynamic Performance , 2012 .

[15]  K. Thole,et al.  Heat Transfer for a Turbine Blade With Nonaxisymmetric Endwall Contouring vortical secondary flows that are present near the endwall of an axial gas , 2011 .

[16]  Remo Marini,et al.  The Effect of Blade Leading Edge Platform Shape on Upstream Disk Cavity to Mainstream Flow Interaction of a High-Pressure Turbine Stage , 2007 .

[17]  T. J. Praisner,et al.  Application of Nonaxisymmetric Endwall Contouring to Conventional and High-Lift Turbine Airfoils , 2013 .

[18]  Reza S. Abhari,et al.  Influence of Rim Seal Purge Flow on Performance of an Endwall-Profiled Axial Turbine , 2009 .

[19]  Steen A. Sjolander,et al.  Effects of an Upstream Cavity on the Secondary Flow in a Transonic Turbine Cascade , 2010 .

[20]  T. J. Praisner,et al.  Measurements of Losses and Reynolds Stresses in the Secondary Flow Downstream of a Low-Speed Linear Turbine Cascade , 2010 .

[21]  Steen A. Sjolander,et al.  Measurements of Secondary Losses in a High-Lift Front-Loaded Turbine Cascade With the Implementation of Non-Axisymmetric Endwall Contouring , 2009 .

[22]  R. Dénos,et al.  Effect of the hub endwall cavity flow on the flow-field of a transonic high-pressure turbine , 2004 .

[23]  Howard P. Hodson,et al.  Improving Turbine Stage Efficiency and Sealing Effectiveness Through Modifications of the Rim Seal Geometry , 2013 .

[24]  Robert J. Moffat,et al.  Describing the Uncertainties in Experimental Results , 1988 .

[25]  Terrence W. Simon,et al.  Flow Measurements in a First Stage Nozzle Cascade Having Endwall Contouring, Leakage, and Assembly Features , 2013 .

[26]  Karen A. Thole,et al.  The Effect of the Combustor-Turbine Slot and Midpassage Gap on Vane Endwall Heat Transfer , 2011 .

[27]  Howard P. Hodson,et al.  Aerothermal Impact of the Interaction Between Hub Leakage and Mainstream Flows in Highly-Loaded HP Turbine Blades , 2010 .

[28]  Howard P. Hodson,et al.  Effect of the Leakage Flows and the Upstream Platform Geometry on the Endwall Flows of a Turbine Cascade , 2006 .

[29]  Steven R. Manwaring,et al.  Endwall Cavity Flow Effects on Gaspath Aerodynamics in an Axial Flow Turbine: Part I — Experimental and Numerical Investigation , 2000 .

[30]  Glen C Snedden,et al.  THE PERFORMANCE OF A GENERIC NON-AXISYMMETRIC END WALL IN A SINGLE STAGE, ROTATING TURBINE AT ON AND OFF-DESIGN CONDITIONS , 2010 .