Combined numerical and experimental investigation of the micro-hydrodynamics of chevron-based textured patterns influencing conjunctional friction of sliding contacts

Reciprocating and low-speed sliding contacts can experience increased friction because of solid boundary interactions. Use of surface texturing has been shown to mitigate undue boundary friction and improve energy efficiency. A combined numerical and experimental investigation is presented to ascertain the beneficial effect of pressure perturbation caused by micro-hydrodynamics of entrapped reservoirs of lubricant in cavities of textured forms as well as improved micro-wedge flow. The results show good agreement between numerical predictions and experimental measurements using a precision sliding rig with a floating bed-plate. Results show that the texture pattern and distribution can be optimised for given conditions, dependent on the intended application under laboratory conditions. The translation of the same into practical in-field applications must be carried out in conjunction with the cost of fabrication and perceived economic gain. This means that near optimal conditions may suffice for most application areas and in practice lesser benefits may accrue than that obtained under ideal laboratory conditions.

[1]  H. Elrod.  A Cavitation Algorithm , 1981 .

[2]  D. C. Evans,et al.  The shear properties of Langmuir—Blodgett layers , 1982, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.

[3]  M. Teodorescu,et al.  Dry and wet nano-scale impact dynamics of rough surfaces with or without a self-assembled monolayer , 2007 .

[4]  Roberto F. Ausas,et al.  The Impact of the Cavitation Model in the Analysis of Microtextured Lubricated Journal Bearings , 2007 .

[5]  Staffan Jacobson,et al.  Influence of surface texture on boundary lubricated sliding contacts , 2003 .

[6]  Homer Rahnejat,et al.  Isothermal transient analysis of piston skirt-to-cylinder wall contacts under combined axial, lateral and tilting motion , 2005 .

[7]  I. Etsion,et al.  Improving Tribological Performance of Piston Rings by Partial Surface Texturing , 2005 .

[8]  Izhak Etsion,et al.  A Laser Surface Textured Parallel Thrust Bearing , 2003 .

[9]  Shoichi Furuhama,et al.  New Device for the Measurement of Piston Frictional Forces in Small Engines , 1983 .

[10]  Homer Rahnejat,et al.  Direct measurement of piston friction of internal-combustion engines using the floating-liner principle , 2014 .

[11]  Homer Rahnejat,et al.  Integrated Tribological Analysis within a Multi- physics Approach to System Dynamics , 2005 .

[12]  Homer Rahnejat,et al.  TRIBOLOGY OF PARTIAL PAD JOURNAL BEARINGS WITH TEXTURED SURFACES , 2011 .

[13]  Homer Rahnejat,et al.  Nanoscale elastoplastic adhesion of wet asperities , 2013 .

[14]  C. Arcoumanis,et al.  Development of a Piston-Ring Lubrication Test-Rig and Investigation of Boundary Conditions for Modelling Lubricant Film Properties , 1995 .

[15]  Izhak Etsion,et al.  Friction-Reducing Surface-Texturing in Reciprocating Automotive Components , 2001 .

[16]  Andreas Almqvist,et al.  A numerical model to investigate the effect of honing angle on the hydrodynamic lubrication between a combustion engine piston ring and cylinder liner , 2011 .

[17]  Yu. G. Schneider,et al.  Formation of surfaces with uniform micropatterns on precision machine and instruments parts , 1984 .

[18]  Kôji Katô,et al.  The effect of laser texturing of SiC surface on the critical load for the transition of water lubrication mode from hydrodynamic to mixed , 2001 .

[19]  Hisung Lee,et al.  A numerical solution to the elastohydrodynamic problem incorporating a non-newtonian rheological model , 1991 .

[20]  X. Q Yu,et al.  Frictional characteristics of mechanical seals with a laser-textured seal face , 2002 .

[21]  Izhak Etsion,et al.  A Model for Mechanical Seals with Regular Microsurface Structure , 1996 .

[22]  Izhak Etsion.  State of the Art in Laser Surface Texturing , 2004 .

[23]  Homer Rahnejat,et al.  In-Cylinder Friction Reduction Using a Surface Finish Optimization Technique , 2006 .

[24]  H. Eyring.  Viscosity, Plasticity, and Diffusion as Examples of Absolute Reaction Rates , 1936 .

[25]  Homer Rahnejat,et al.  Investigation of Reciprocating Conformal Contact of Piston Skirt-to-Surface Modified Cylinder Liner in High Performance Engines , 2005 .

[26]  H Rahnejat,et al.  Physio-chemical hydrodynamic mechanism underlying the formation of thin adsorbed boundary films. , 2012, Faraday discussions.

[27]  C. Coulomb.  Théorie des machines simples, en ayant égard au frottement de leurs parties et a la roideur des cordages , 1968 .

[28]  Staffan Jacobson,et al.  Textured surfaces for improved lubrication at high pressure and low sliding speed of roller/piston in hydraulic motors , 2007 .

[29]  H. Rahnejat,et al.  Fundamentals Of Tribology , 2008 .

[30]  Martin Hartl,et al.  The effect of surface texturing on thin EHD lubrication films , 2007 .

[31]  J. Greenwood,et al.  The Contact of Two Nominally Flat Rough Surfaces , 1970 .

[32]  Homer Rahnejat,et al.  Multi-Body Dynamics: Vehicles, Machines and Mechanisms , 1998 .

[33]  Yoshiteru Yasuda,et al.  Effect of surface texturing on friction reduction between ceramic and steel materials under lubricated sliding contact , 2003 .

[34]  Izhak Etsion,et al.  Experimental Investigation of Laser Surface Texturing for Reciprocating Automotive Components , 2002 .

[35]  Kôji Katô,et al.  Loads carrying capacity map for the surface texture design of SiC thrust bearing sliding in water , 2003 .

[36]  I. Etsion,et al.  Improving fuel efficiency with laser surface textured piston rings , 2009 .

[37]  Hassan Shirvani,et al.  Optimization of Partially Textured Parallel Thrust Bearings With Square-Shaped Micro-Dimples , 2006 .

[38]  Izhak Etsion,et al.  Experimental Investigation of Laser Surface Textured Parallel Thrust Bearings , 2004 .

[39]  Ali Erdemir,et al.  Review of engineered tribological interfaces for improved boundary lubrication , 2005 .

[40]  S. Theodossiades,et al.  Influence of In-Plane Dynamics of Thin Compression Rings on Friction in Internal Combustion Engines , 2012 .

[41]  Homer Rahnejat,et al.  Reducing in-cylinder parasitic losses through surface modification and coating , 2014 .

[42]  I. Etsion,et al.  Surface texturing for in-cylinder friction reduction , 2010 .

[43]  Ozgen Akalin,et al.  Piston Ring-Cylinder Bore Friction Modeling in Mixed Lubrication Regime: Part I—Analytical Results , 2001 .

[44]  D. Dowson,et al.  A Numerical Solution to the Elasto-Hydrodynamic Problem , 1959 .

[45]  W.W.F. Chong,et al.  Elastoplastic contact of rough surfaces: a line contact model for boundary regime of lubrication , 2014 .

[46]  I. Etsion,et al.  Testing piston rings with partial laser surface texturing for friction reduction , 2006 .

[47]  Homer Rahnejat,et al.  Thermo-Mixed Hydrodynamics of Piston Compression Ring Conjunction , 2013, Tribology Letters.

[48]  W. 0. Winer,et al.  Correlational Aspects of the Viscosity-Temperature-Pressure Relationship of Lubricating Oils(Dr In dissertation at Technical University of Delft, 1966) , 1966 .

[49]  S B Donkin,et al.  DISCUSSION OF 4809 & 4826. AN EXPERIMENTAL DETERMINATION OF THE DISTRIBUTION AND THICKNESS OF THE OIL FILM IN A FLOODED CYLINDRICAL BEARING. THE STABILITY OF LUBRICATING FILMS IN JOURNAL BEARINGS. , .

[50]  Ian M. Hutchings,et al.  Hydrodynamic lubrication of textured steel surfaces under reciprocating sliding conditions , 2007 .

[51]  H. Rahnejat,et al.  Tribology of compression ring-to-cylinder contact at reversal , 2008 .

[52]  William Bate Hardy,et al.  Boundary Lubrication. The Paraffin Series , 1922 .