A reference device for evaluating the thermal behavior of installed multilayered wall containing a phase change material

Abstract Thermal inertia of lightweight building envelopes can be improved including phase change materials in multilayered wallboards. The thermal modeling of buildings for design purposes needs a robust description of the thermal properties of installed phase change materials. A standard method would improve the thermal characterization of commercial products. The aim of the study is to develop a simple methodology to obtain reliable thermal data for phase change materials integrated in multilayered wallboards. The methodology modifies differential scanning calorimetry measurements on phase change material by installation factors to obtain the apparent specific heat vs. temperature for the wallboard layer embedding phase change material. Simple cubic cells were realized as reference devices to simulate a confined environment. A dynamic model of heat transfer was developed to simulate the thermal behavior of devices. Installation factors were calculated by regression of the monitored temperatures inside and outside the devices operating under real environmental conditions. The apparent specific heat of phase change material, measured by differential scanning calorimetry at different rates, resulted in a spread of curves vs. temperature. Mean curves were used as initial condition for regression. The mean calculation method did not significantly affect the installed resulted curve. A unique curve of apparent specific heat vs. temperature best fit data measured over a wide range of experimental devices and conditions. Good regression performances were observed for solid liquid and biphasic states with different thickness of the phase change material layer. The modification of differential scanning calorimetry measurements through installation factors improved the robustness of description. The proposed methodology could be a starting point for the definition of a reference standard for the characterization and comparison of wallboards embedding phase change materials.

[1]  Guido Sassi,et al.  Uncertainty analysis of the diffusion rate in the dynamic generation of volatile organic compound mixtures , 2011 .

[2]  Romeu Vicente,et al.  Brick masonry walls with PCM macrocapsules: An experimental approach , 2014 .

[3]  Oliver Kornadt,et al.  Temperature reduction due to the application of phase change materials , 2008 .

[4]  Joseph Virgone,et al.  Energetic efficiency of room wall containing PCM wallboard: A full-scale experimental investigation , 2008 .

[5]  Luisa F. Cabeza,et al.  Experimental study of using PCM in brick constructive solutions for passive cooling , 2010 .

[6]  M. N. Özişik,et al.  Finite Difference Methods in Heat Transfer , 2017 .

[7]  André Bontemps,et al.  Thermal testing and numerical simulation of a prototype cell using light wallboards coupling vacuum isolation panels and phase change material , 2006 .

[8]  Luisa F. Cabeza,et al.  Review on thermal energy storage with phase change: materials, heat transfer analysis and applications , 2003 .

[9]  Jose Manuel Cejudo-Lopez,et al.  Uncertainty in peak cooling load calculations , 2010 .

[10]  Panayiotis A. Kyriacou,et al.  Improved measurement technique for the characterization of organic and inorganic phase change materials using the T-history method , 2013 .

[11]  L. Cabeza,et al.  Review of the T-history method to determine thermophysical properties of phase change materials (PCM) , 2013 .

[12]  Andreas K. Athienitis,et al.  Investigation of the Thermal Performance of a Passive Solar Test-Room with Wall Latent Heat Storage , 1997 .

[13]  Luisa F. Cabeza,et al.  Determination of the enthalpy of PCM as a function of temperature using a heat‐flux DSC—A study of different measurement procedures and their accuracy , 2008 .

[14]  R. Ramanathan,et al.  Introductory Econometrics With Applications , 1989 .

[15]  Luisa F. Cabeza,et al.  Materials used as PCM in thermal energy storage in buildings: A review , 2011 .

[16]  Lv Shilei,et al.  Impact of phase change wall room on indoor thermal environment in winter , 2006 .

[17]  L. Cabeza,et al.  Determination of enthalpy?temperature curves of phase change materials with the temperature-history method: improvement to temperature dependent properties , 2003 .

[18]  Frédéric Kuznik,et al.  A review on phase change materials integrated in building walls , 2011 .

[19]  Amar M. Khudhair,et al.  A review on phase change energy storage: materials and applications , 2004 .

[20]  K. Nagarajan,et al.  Evaluation of heat capacity measurements by temperature-modulated differential scanning calorimetry , 2010 .

[21]  Paul Strachan,et al.  Practical application of uncertainty analysis , 2001 .

[22]  Joseph Virgone,et al.  Experimental investigation of wallboard containing phase change material: Data for validation of numerical modeling , 2009 .

[23]  Zhang Yinping,et al.  A simple method, the -history method, of determining the heat of fusion, specific heat and thermal conductivity of phase-change materials , 1999 .

[24]  Luisa F. Cabeza,et al.  Use of microencapsulated PCM in concrete walls for energy savings , 2007 .

[25]  Xiaoqin Sun,et al.  Energy and economic analysis of a building enclosure outfitted with a phase change material board (PCMB) , 2014 .

[26]  Dieter Boer,et al.  Uncertainty propagation and sensitivity analysis of thermo-physical properties of phase change materials (PCM) in the energy demand calculations of a test cell with passive latent thermal storage , 2015 .

[27]  R. Velraj,et al.  Experimental investigation and numerical simulation analysis on the thermal performance of a building roof incorporating phase change material (PCM) for thermal management , 2008 .

[28]  D. Feldman,et al.  Full scale thermal testing of latent heat storage in wallboard , 1996 .

[29]  Gilles Guyon,et al.  Application of parameters space analysis tools for empirical model validation , 2004 .

[30]  Na Zhu,et al.  Dynamic characteristics and energy performance of buildings using phase change materials: A review , 2009 .

[31]  Shazim Ali Memon,et al.  Phase change materials integrated in building walls: A state of the art review , 2014 .

[32]  L. Cabeza,et al.  Study on differential scanning calorimetry analysis with two operation modes and organic and inorganic phase change material (PCM) , 2013 .

[33]  Yongsheng Lian,et al.  Numerical simulation of phase change material composite wallboard in a multi-layered building envelope , 2012 .

[34]  Godfried Augenbroe,et al.  Analysis of uncertainty in building design evaluations and its implications , 2002 .

[35]  Dong Li,et al.  Numerical analysis on thermal performance of roof contained PCM of a single residential building , 2015 .

[36]  Joseph Virgone,et al.  Optimization of a Phase Change Material Wallboard for Building Use , 2008 .

[37]  Laurent Mora,et al.  Practical application of uncertainty analysis and sensitivity analysis on an experimental house , 2012 .

[38]  Guido Sassi,et al.  Characterization of panels containing micro-encapsulated Phase Change Materials , 2013 .

[39]  Harald Mehling,et al.  Enthalpy of Phase Change Materials as a Function of Temperature: Required Accuracy and Suitable Measurement Methods , 2009 .

[40]  Jose M. Marin,et al.  Verification of a T-history installation to measure enthalpy versus temperature curves of phase change materials , 2006 .

[41]  H. Hong,et al.  Accuracy improvement of T-history method for measuring heat of fusion of various materials , 2004 .

[42]  Paulo Cesar Tabares-Velasco.  Energy Impacts of Nonlinear Behavior of PCM When Applied Into Building Envelope , 2012 .

[43]  Jlm Jan Hensen,et al.  Uncertainty analysis in building performance simulation for design support , 2011 .

[44]  Harry Boyer,et al.  A thermal model for phase change materials in a building roof for a tropical and humid climate: Model description and elements of validation , 2014 .