A study on the formability of aluminum tailor welded blanks produced by friction stir welding

Tailored welded blanks (TWBs) technology can give an important possibility to obtain components in automobile industry satisfying lightweight strategies as well as satisfying increased crashworthiness, corrosion resistance, and accuracy. Friction stir welding (FSW) is a joining process, which can be well fitted to obtaining aluminum tailored blanks when compared to other conventional joining processes. This paper presents an experimental study on TWBs produced by FSW with dissimilar aluminum alloy thin sheets. The formability performance is investigated by obtaining forming limit curves with Nakajima test using different blank widths. The properties of welded AA5182/AA6061 alloy pair, 1 mm thick, are studied and the corresponding formability is compared to base materials. Different weld line orientations are defined related to sheet rolling direction and corresponding forming limit curves are obtained in addition to load–displacement behavior. Results show a dependency of TWB formability on weld line orientation, as well as a decrease of welded pair alloy formability when compared to base materials.

[1]  Taylan Altan,et al.  Deep drawing of round cups from tailor-welded blanks , 1995 .

[2]  T. DebRoy,et al.  Porosity, underfill and magnesium loss during continuous wave Nd:YAG laser welding of thin plates of aluminum alloys 5182 and 5754 , 1999 .

[3]  W. S. Miller,et al.  Recent development in aluminium alloys for the automotive industry , 2000 .

[4]  Subra Suresh,et al.  DETERMINATION OF ELASTO-PLASTIC PROPERTIES BY INSTRUMENTED SHARP INDENTATION: GUIDELINES FOR PROPERTY EXTRACTION , 2000 .

[5]  K. Hono,et al.  The effect of Cu additions on the precipitation kinetics in an Al-Mg-Si alloy with excess Si , 2001 .

[6]  W. Chien,et al.  A combined necking and shear localization analysis for aluminum sheets under biaxial stretching conditions , 2004 .

[7]  Hiroyuki Kokawa,et al.  Post-weld formability of friction stir welded Al alloy 5052 , 2004 .

[8]  Michael Miles,et al.  Formability of friction-stir-welded dissimilar-aluminum-alloy sheets , 2005 .

[9]  Pedro Vilaça,et al.  Material flow in heterogeneous friction stir welding of thin aluminium sheets: Effect of shoulder geometry , 2008 .

[10]  Altino Loureiro,et al.  Effect of overlapping friction stir welding passes in the quality of welds of aluminium alloys , 2008 .

[11]  Z. Sheng.  Formability of tailor-welded strips and progressive forming test , 2008 .

[12]  Y. Bréchet,et al.  Precipitation microstructures in an AA6056 aluminium alloy after friction stir welding: Characterisation and modelling , 2008 .

[13]  S. Panda,et al.  Formability Analysis of Diode-Laser-Welded Tailored Blanks of Advanced High-Strength Steel Sheets , 2009 .

[14]  R. M. Leal,et al.  Influence of friction stir welding parameters on the microstructural and mechanical properties of AA 6016-T4 thin welds , 2009 .

[15]  Dulce Maria Rodrigues,et al.  Formability of similar and dissimilar friction stir welded AA 5182-H111 and AA 6016-T4 tailored blanks , 2009 .

[16]  Anthony P. Reynolds,et al.  Multi-Pass Friction Stir Welding in Alloy 7050-T7451: Effects on Weld Response Variables and on Weld Properties , 2009 .

[17]  Kwansoo Chung,et al.  Experimental and numerical study on formability of friction stir welded TWB sheets based on hemispherical dome stretch tests , 2009 .

[18]  K. Chung,et al.  Formability evaluation of friction stir welded 6111-T4 sheet with respect to joining material direction , 2010 .

[19]  Kwansoo Chung,et al.  Macro-performance evaluation of friction stir welded automotive tailor-welded blank sheets: Part II – Formability , 2010 .

[20]  Bo Zhang,et al.  Influence of weld geometry and mismatch on formability of aluminium tailor welded blanks: numerical and experimental analysis , 2011 .

[21]  Jwo Pan,et al.  Modeling of failure mode of laser welds in lap-shear specimens of HSLA steel sheets , 2011 .

[22]  J. Pan,et al.  Failure mode of laser welds in lap-shear specimens of high strength low alloy (HSLA) steel sheets , 2012 .

[23]  L. Hua,et al.  Influence of inhomogeneous constitutive properties of weld materials on formability of tailor welded blanks , 2012 .

[24]  Xin Sun,et al.  Quasi-static and dynamic responses of advanced high strength steels: Experiments and modeling , 2012 .

[25]  Hassan Moslemi Naeini,et al.  Forming Limit Diagram Prediction of Tailor-Welded Blank Using Experimental and Numerical Methods , 2012, Journal of Materials Engineering and Performance.

[26]  H. Moslemi Naeini,et al.  Experimental and theoretical investigation of thickness ratio effect on the formability of tailor welded blank , 2013 .

[27]  Effect of Weld Line Orientation on Formability of Tailor Welded Blank of 22MnB5 at Elevated Temperature , 2015 .