Coffin-Manson based fatigue analysis of underfilled DCAs

The continuing drive toward high-density, low-profile Integrated Circuit packaging has accelerated the spread of flip-chip technology to laminated substrates, creating direct chip attach (DCA) configurations. However, the substantial difference in the coefficients of thermal expansion (CTE) between the chip and the laminated substrates makes DCA configurations vulnerable to thermally-induced strains and the resulting solder joint fatigue. The reliability of flip-chip technology is dramatically improved by “underfilling” the gap between the chip and substrate with epoxy. The present effort is aimed at exploring the benefits of underfilling in DCA configurations. The thermo-structural behavior of an underfilled DCA is evaluated using FEM and employing an axisymmetric model of a typical DCA structure. Numerical simulations are performed for different sets of underfill material properties. The results are used to determine the parametric sensitivity of the thermal strain in the solder joints and the axial and shear stresses in the underfill material and to define the desirable range of underfill material properties. These results together with the Coffin-Manson relation are used to predict the theoretical improvement in cycles to failure. The results suggest that to minimize fatigue failure, the CTE of an underfill material should match that of solder material and its Young's Modulus should be as high as the adhesion strength of the underfill allows.

[1]  A. S. Chen,et al.  A study of the interactions of molding compound and die attach adhesive, with regards to package cracking , 1994, 1994 Proceedings. 44th Electronic Components and Technology Conference.

[2]  C. W. Nelson,et al.  Thermal stress in bonded joints , 1979 .

[3]  Abhijit Dasgupta,et al.  A Nonlinear Multi-Domain Stress Analysis Method for Surface-Mount Solder Joints , 1996 .

[4]  H. Melchior,et al.  Low cost packaging of semiconductor laser arrays using passive self-aligned flip-chip technique on Si motherboard , 1996, 1996 Proceedings 46th Electronic Components and Technology Conference.

[5]  M. Rothman,et al.  Monolithically integrated laser/rear-facet monitor arrays with V-groove for passive optical fiber alignment , 1993, IEEE Photonics Technology Letters.

[6]  Jeannine M. Trewhella,et al.  A compact multichannel transceiver module using planar-processed optical waveguides and flip-chip optoelectronic components , 1992, 1992 Proceedings 42nd Electronic Components & Technology Conference.

[7]  Hyung-Moo Park,et al.  Optical device module packages for subscriber incorporating passive alignment techniques , 1995, 1995 Proceedings. 45th Electronic Components and Technology Conference.

[8]  W. Engelmaier.  Fatigue Life of Leadless Chip Carrier Solder Joints During Power Cycling , 1983 .

[9]  Yung-Cheng Lee,et al.  Effects of Ceramic Ball-Grid-Array Package’s Manufacturing Variations on Solder Joint Reliability , 1994 .

[10]  M. Tabasky,et al.  Passive coupling of InGaAsP/InP laser array and singlemode fibres using silicon waferboard , 1991 .

[11]  Ephraim Suhir.  Thermally induced interfacial stresses in elongated bimaterial plates , 1989 .

[12]  G. O'Malley,et al.  The importance of material selection for flip chip on board assemblies , 1994, 1994 Proceedings. 44th Electronic Components and Technology Conference.

[13]  B. Z. Hong,et al.  Nonlinear finite element simulation of thermoviscoplastic deformation of C4 solder joints in high density packaging under thermal cycling , 1994, Proceedings of 1994 4th Intersociety Conference on Thermal Phenomena in Electronic Systems (I-THERM).

[14]  E. K. Buratynski.  Analysis of Bending and Shearing of Tri-Layer Laminations for Solder Joint Reliability , 1998 .

[15]  E. Sugita,et al.  Miniature optical connector with small zirconia ferrule , 1991, IEEE Photonics Technology Letters.

[16]  T. Hayashi,et al.  An innovative bonding technique for optical chips using solder bumps that eliminate chip positioning adjustments , 1992 .

[17]  A. Bar-Cohen,et al.  Thermo-structural behavior of underfilled flip-chips , 1996, 1996 Proceedings 46th Electronic Components and Technology Conference.

[18]  Satoru Yamaguchi,et al.  Optical waveguide interconnections for optoelectronic multichip modules , 1993, Photonics West - Lasers and Applications in Science and Engineering.

[19]  J. O. Hallquist,et al.  NIKE2D: A nonlinear, implicit, two-dimensional finite element code for solid mechanics , 1991 .

[20]  Konstantinos I. Papathomas,et al.  Encapsulant for fatigue life enhancement of controlled-collapse chip connection (C4) , 1993 .

[21]  K. Katsura,et al.  Micro-alignment technique using 26-/spl mu/m diameter microsolder bumps and its shear strength , 1995, Proceedings of 1995 Japan International Electronic Manufacturing Technology Symposium.

[22]  M. Tabasky,et al.  Four-channel, long-wavelength transmitter arrays incorporating passive laser/singlemode-fiber alignment on silicon waferboard , 1992, 1992 Proceedings 42nd Electronic Components & Technology Conference.

[23]  M. Tabasky,et al.  Gigabit transmitter array modules on silicon waferboard , 1992 .

[24]  Steven C. Machuga,et al.  The importance of material selection for flip chip on board assemblies , 1994 .

[25]  G. Hill,et al.  Flip-chip encapsulation on ceramic substrates , 1993, Proceedings of IEEE 43rd Electronic Components and Technology Conference (ECTC '93).

[26]  E. Bassous,et al.  Passive laser-fiber alignment by index method , 1991, IEEE Photonics Technology Letters.

[27]  B. Mirman.  Microelectronics and the Built-Up-Bar Theory , 1992 .

[28]  Douglas O. Powell,et al.  Flip-chip on FR-4 integrated circuit packaging , 1993, Proceedings of IEEE 43rd Electronic Components and Technology Conference (ECTC '93).

[29]  Naoya Kukutsu,et al.  Accurate, stable, high-speed interconnections using 20- to 30-/spl mu/m-diameter microsolder bumps , 1997 .

[30]  M. N. Nguyen,et al.  Low stress polymer die attach adhesive for plastic packages , 1994, 1994 Proceedings. 44th Electronic Components and Technology Conference.

[31]  Alan G. Klopfenstein.  Microelectronics Packaging Handbook , 1997, Springer US.

[32]  A. Bar-Cohen,et al.  Mechanistic figures of merit for die-attach materials , 1996, InterSociety Conference on Thermal Phenomena in Electronic Systems, I-THERM V.