Thin-Film Encapsulated RF MEMS Switches

A wafer-level thin-film encapsulation process has been demonstrated to package radio-frequency (RF) microelectromechanical systems (MEMS) switches in this paper. Individual shunt capacitive switches were packaged in a ~1nL inorganic enclosure with process temperatures not exceeding 300 degC. A shell covering the switch consisted of 10 nm of sputtered alumina and 1.67 mum of sputtered silicon nitride dielectric film. The switch and dielectric shell were simultaneously wet-released through access channels in the shell. Following release, access channels were sealed with 10 nm of sputtered alumina and 2-4 mum of either plasma-enhanced chemical vapor deposited silicon dioxide or silicon nitride. Electromagnetic simulation and RF test results before and after sealing show minimal RF degradation of switch performance. Before sealing, the insertion loss and isolation at 10 GHz averaged 0.12 and 10.7 dB, respectively. After sealing, the same devices had an average insertion loss and isolation of 0.12 and 10.1 dB, respectively. Complete characterization of the package atmosphere was not completed due to challenges in assessing nanoliter-scale volumes

[1]  Elliott R. Brown,et al.  RF-MEMS switches for reconfigurable integrated circuits , 1998 .

[2]  B. Akkal,et al.  Study and characterization of the structures Au/Al2O3/Si and Au/Al0/Al2O3/Si , 2002 .

[3]  Y. Tai,et al.  Sealing of micromachined cavities using chemical vapor deposition methods: characterization and optimization , 1999 .

[4]  C. Goldsmith,et al.  Micromechanical membrane switches for microwave applications , 1995, Proceedings of 1995 IEEE MTT-S International Microwave Symposium.

[5]  J.L. Ebel,et al.  A Latching Capacitive RF MEMS Switch in a Thin Film Package , 2006, 2006 IEEE MTT-S International Microwave Symposium Digest.

[6]  Per Wallgren,et al.  Spin deposition of polymers over holes and cavities , 1995 .

[7]  Khalil Najafi.  Micropackaging Technologies for Integrated Microsystems: Applications to MEMS and MOEMS , 2003, SPIE MOEMS-MEMS.

[8]  Metallization schemes for radio frequency microelectromechanical system switches , 2003 .

[9]  Wafer-scale film encapsulation of micromachined accelerometers , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[10]  M. Guillorn,et al.  A microfabrication process for a vacuum-encapsulated microchamber , 2005 .

[11]  D. M. Drury,et al.  Monolithic 2-18 GHz low loss, on-chip biased PIN diode switches , 1995 .

[12]  L.P.B. Katehi,et al.  Fabrication and accelerated hermeticity testing of an on-wafer package for RF MEMS , 2004, IEEE Transactions on Microwave Theory and Techniques.

[13]  David I. Forehand,et al.  Wafer Level Micropackaging for RF MEMS Switches , 2005 .

[14]  Ching-Ping Wong,et al.  Novel bi-layer conformal coating for reliability without hermeticity MEMS encapsulation , 1999 .

[15]  K. Najafi,et al.  A low-temperature thin-film electroplated metal vacuum package , 2004, Journal of Microelectromechanical Systems.

[16]  Liwei Lin.  MEMS post-packaging by localized heating and bonding , 2000 .

[17]  M. Shokrani,et al.  InGaAs microwave switch transistors for phase shifter circuits , 1994 .

[18]  M. Madou.  Fundamentals of microfabrication , 1997 .

[19]  Francis Pressecq,et al.  Environmental test bench for reliability studies: influence of the temperature on rf switches with metallic membranes , 2002, Symposium on Design, Test, Integration, and Packaging of MEMS/MOEMS.

[20]  D. Beebe,et al.  The fabrication of nonplanar spin-on glass microstructures , 1999 .