CFD NUMERICAL AND EXPERIMENTAL INVESTIGATION OF TWO-PHASE FLOW DEVELOPMENT AFTER AN EXPANSION DEVICE IN A HORIZONTAL PIPE

To optimize a vertical flash tank separator, the characteristics of the flow entering the separator are required to be known. A flash tank separator improves the performance of a refrigeration cycle by separating the liquid from liquid-gas flow and providing the evaporator with only liquid refrigerant. This technique improves the effective area and enhances the heat transfer coefficient in the evaporator. This paper investigates the influence of the inlet operating conditions to an expansion device, on the adiabatic two-phase flow development in a horizontal pipe downstream from the expansion device. This work also compares three dimensional numerical simulations and experimental observations for the two-phase flow development after the expansion device in the horizontal pipe. A general trend of the two-phase flow after the expansion device was gradually developed and the expansion length was identified at less than 200 mm from the inlet. The two-phase flow behaviour was recorded using a digital camera recording the flow behaviour at the upstream and downstream of the horizontal tube. The results revealed that an increase of the mass flow rate causes an increase in the void fraction and a reduction in the slip ratio in the developed region. The simulations underestimate the expansion length and the mean difference between the experimental data and the numerical results is 8 %

[1]  O. Parkash.  FLOW CHARACTERIZATION OF MULTI-PHASE PARTICULATE SLURRY IN THERMAL POWER PLANTS USING COMPUTATIONAL FLUID DYNAMICS , 2020 .

[2]  D. Buttsworth,et al.  Computational and Experimental Investigation of using an Extractor in the Vertical Gravitational Flash Tank Separator , 2019, International Journal of Automotive and Mechanical Engineering.

[3]  D. Buttsworth,et al.  Computational and Experimental Investigation of the Vertical Flash Tank Separator Part 1: Effect of Parameters on Separation Efficiency , 2019, International Journal of Air-Conditioning and Refrigeration.

[4]  Jamie S. Ervin,et al.  Flow pattern identification of horizontal two-phase refrigerant flow using neural networks , 2016 .

[5]  O. Mahian,et al.  Measurement of the void fraction of R-134a flowing through a horizontal tube , 2014 .

[6]  K. B. Rana,et al.  Measurement of void fraction in flow boiling of ZnO–water nanofluids using image processing technique , 2014 .

[7]  Michel Lance,et al.  Experimental investigation of a developing two-phase bubbly flow in horizontal pipe , 2014 .

[8]  S. aus der Wiesche,et al.  Numerical Simulation of Single Bubble Dynamics During Flow Boiling Conditions on a Horizontal Surface , 2014 .

[9]  Jun Zhou,et al.  Numerical modeling for stratified gas–liquid flow and heat transfer in pipeline , 2014 .

[10]  Jian Xie,et al.  Stratified two-phase flow pattern modulation in a horizontal tube by the mesh pore cylinder surface , 2013 .

[11]  陈光文,et al.  Gas–liquid two-phase flow in microchannel at elevated pressure , 2013 .

[12]  Tapas Kumar Mandal,et al.  CFD Simulation and Validation of Flow Pattern Transition Boundaries during Moderately Viscous Oil-Water Two-Phase Flow through Horizontal Pipeline , 2013 .

[13]  P. Hrnjak,et al.  Condensation from superheated vapor flow of R744 and R410A at subcritical pressures in a horizontal smooth tube , 2012 .

[14]  Jacob H. Masliyah,et al.  CFD Modeling of Gas-Liquid Bubbly Flow in Horizontal Pipes: Influence of Bubble Coalescence and Breakup , 2012 .

[15]  Ren Tong,et al.  CFD simulation of separation of two-phase flows systems , 2011, 2011 Second International Conference on Mechanic Automation and Control Engineering.

[16]  I. Teke,et al.  Comparison of frictional pressure drop models during annular flow condensation of R600a in a horizontal tube at low mass flux and of R134a in a vertical tube at high mass flux , 2010 .

[17]  Thomas S.Y. Choong,et al.  Numerical study of dispersed oil–water turbulent flow in horizontal tube , 2009 .

[18]  K. V. Sharma,et al.  CFD Analysis of Two Phase Flow in a Horizontal Pipe - Prediction of Pressure Drop , 2008 .

[19]  Josua P. Meyer,et al.  Horizontal two-phase flow characterization for small diameter tubes with a capacitance sensor , 2007 .

[20]  A. Bannari,et al.  CFD MODELING OF GAS DISPERSION AND BUBBLE SIZE IN A DOUBLE TURBINE STIRRED TANK , 2006 .

[21]  P. Hrnjak,et al.  Developing Adiabatic Two Phase Flow in Headers—Distribution Issue in Parallel Flow Microchannel Heat Exchangers , 2004 .

[22]  J. Thome,et al.  Condensation in Horizontal Tubes, Part 1: Two-Phase Flow Pattern Map , 2003 .

[23]  I. Hassan,et al.  STEAM-WATER STRATIFIED FLOW IN T-JUNCTIONS – EXPERIMENTS AND MODELLING , 2002 .

[24]  R. C. Xin,et al.  Measurement and correlation of the pressure drop in air-water two-phase flow in horizontal helicoidal pipes , 1995 .

[25]  J. Thome,et al.  New prediction methods for CO2 evaporation inside tubes: Part I – A two-phase flow pattern map and a flow pattern based phenomenological model for two-phase flow frictional pressure drops , 2008 .

[26]  Predrag Stojan Hrnjak,et al.  Using Change Point Analysis for Image Processing of Developing Adiabatic Two-Phase Flow After Expansion Valve , 2007 .

[27]  P. Hrnjak,et al.  Adiabatic Developing Two-Phase Refrigerant Flow in Manifolds of Heat Exchangers , 2004 .