Effect of milling parameters on sinterability, mechanical and electrical properties of Cu-4 wt.% ZrO2 nanocomposite

[1]  M. Fichtner,et al.  Production of nanocrystalline lithium fluoride by planetary ball-milling , 2014 .

[2]  D. Jeyasimman,et al.  An investigation of the synthesis, consolidation and mechanical behaviour of Al 6061 nanocomposites reinforced by TiC via mechanical alloying , 2014 .

[3]  Jingjing Su,et al.  Effects of ball-to-powder weight ratio on the performance of LiFePO4/C prepared by wet-milling assisted carbothermal reduction , 2014 .

[4]  M. Zawrah,et al.  Mechanical alloying, sintering and characterization of Al2O3–20 wt%–Cu nanocomposite , 2014 .

[5]  C. Suryanarayana,et al.  Mechanically alloyed nanocomposites , 2013 .

[6]  M. Zawrah,et al.  Preparation by mechanical alloying, characterization and sintering of Cu–20 wt.% Al2O3 nanocomposites , 2013 .

[7]  A. Bahrami,et al.  The effect of Si addition on the microstructure and magnetic properties of Permalloy prepared by mechanical alloying method , 2013 .

[8]  A. Çanakçı,et al.  Effects of amount of methanol on characteristics of mechanically alloyed Al–Al2O3 composite powders , 2012 .

[9]  T. Yadav,et al.  Synthesis of nanocrystalline cerium oxide by high energy ball milling , 2012 .

[10]  K. Hariharan,et al.  Mechanical milling: An alternative approach for enhancing the conductivity of SnF2 , 2012 .

[11]  H. Salem,et al.  Effect of milling energy on the structural evolution and stability of nanostructured Al-5.7 wt.% Ni mechanically alloyed eutectic alloy , 2012 .

[12]  M. Zawrah,et al.  Fabrication of Al2O3–20 vol.% Al nanocomposite powders using high energy milling and their sinterability , 2012 .

[13]  C. Suryanarayana.  Synthesis of nanocomposites by mechanical alloying , 2011 .

[14]  H. Shokrollahi,et al.  Magnetic and structural studies of mechanically alloyed nanostructured Fe49Co49V2 powders , 2010 .

[15]  V. Senthilkumar,et al.  Role of nano-size reinforcement and milling on the synthesis of nano-crystalline aluminium alloy composites by mechanical alloying , 2010 .

[16]  H. Henein,et al.  ZrC particle reinforced Al–4 wt.% Cu alloy composites fabricated by mechanical alloying and vacuum hot pressing: Microstructural evaluation and mechanical properties , 2010 .

[17]  M. Öveçoğlu,et al.  Characterization investigations during mechanical alloying and sintering of W–20 vol% SiC composites , 2010 .

[18]  K. Hariharan,et al.  AC conductivity and scaling studies of polycrystalline SnF2 , 2009 .

[19]  D. Božić,et al.  Characteristics of Cu-Al2O3 composites of various starting particle size obtained by high-energy milling , 2009 .

[20]  Eric Forssberg,et al.  Microstructural characterization of hematite during wet and dry millings using Rietveld and XRD line profile analyses , 2008 .

[21]  D. Božić,et al.  Properties of copper matrix reinforced with nano- and micro-sized Al2O3 particles , 2008 .

[22]  D. Božić,et al.  Properties of copper matrix reinforced with various size and amount of Al2O3 particles , 2008 .

[23]  J. D. Arboleda,et al.  Magnetic and structural properties of pure hematite submitted to mechanical milling in air and ethanol , 2007 .

[24]  Y. Liu,et al.  Microstructure and properties at elevated temperature of a nano-Al2O3 particles dispersion-strengthened copper base composite , 2006 .

[25]  Syed Nasimul Alam,et al.  Synthesis and characterization of W–Cu nanocomposites developed by mechanical alloying , 2006 .

[26]  Linan An,et al.  Synthesis and characterization of high volume fraction Al-Al2O3 nanocomposite powders by high-energy milling , 2006 .

[27]  R. Scattergood,et al.  Consolidation of a Cu–2.5 vol.% Al2O3 powder using high energy mechanical milling , 2005 .

[28]  C. Suryanarayana,et al.  Mechanical alloying and milling , 2004 .

[29]  G. Gonzalez,et al.  Effect of the Milling Media on the Phases Obtained in Mechanically Alloyed Equiatomic Fe-Co , 2001 .

[30]  Edward J. Garboczi,et al.  Effects of cement particle size distribution on performance properties of Portland cement-based materials , 1999 .

[31]  J. Poole,et al.  Recent Developments in Mechanical Alloying , 1994 .