Liquid–liquid segmented flows in polycarbonate microchannels with cross-sectional expansions ☆

Abstract Liquid–liquid segmented flows in microchannels fabricated on polycarbonate test chips were investigated experimentally. Three different cross-sectional expansion ratios of 16, 4, and 2 from the injection to the test channels were used to observe the effect of different cross-sectional areas of the injection channel on the segmented flow regimes in the test channel. Flow regime maps and the transitions between flow regimes were determined for the different expansion ratios. The effect of the cross-sectional expansion ratio was determined by mutual comparison of these results. The measured length of the dispersed fluid segments was found to scale inversely with the carrier fluid volumetric flow ratio ( β C ). A simplified geometric model for the volume of the dispersed and the carrier fluid plugs provided good estimates of the carrier plug length, which scaled inversely with (1 −  β C ). Velocity and pressure drop measurements of the liquid–liquid segmented flows were carried out for all flow regimes, and the associated trends were correlated with changes in the flow topology. Most previous homogeneous and separated flow models based on the viscous frictional pressure drop underestimated the measured pressure drops. Including the contribution of the capillary pressure drop in addition to the frictional pressure drop improved the agreement with the measured data.

[1]  F. K. Hansen,et al.  Surface tension by pendant drop , 1991 .

[2]  Helen Song,et al.  A microfluidic system for controlling reaction networks in time. , 2003, Angewandte Chemie.

[3]  Akio Tomiyama,et al.  Terminal velocity of a Taylor drop in a vertical pipe , 2011 .

[4]  Shanavaz Nasarabadi,et al.  On-chip single-copy real-time reverse-transcription PCR in isolated picoliter droplets. , 2007, Analytical chemistry.

[5]  Matthias Heil,et al.  The steady propagation of a semi-infinite bubble into a tube of elliptical or rectangular cross-section , 2002, Journal of Fluid Mechanics.

[6]  Minoru Seki,et al.  Hydrodynamic control of droplet division in bifurcating microchannel and its application to particle synthesis. , 2008, Journal of colloid and interface science.

[7]  J. Burns,et al.  The intensification of rapid reactions in multiphase systems using slug flow in capillaries. , 2001, Lab on a chip.

[8]  D. Nikitopoulos,et al.  Gas–liquid two-phase flows in rectangular polymer micro-channels , 2011 .

[9]  Johan Roeraade,et al.  Continuous segmented-flow polymerase chain reaction for high-throughput miniaturized DNA amplification. , 2003, Analytical chemistry.

[10]  David N. Adamson,et al.  Production of arrays of chemically distinct nanolitre plugs via repeated splitting in microfluidic devices. , 2006, Lab on a chip.

[11]  David R. Emerson,et al.  Numerical and experimental study of a droplet-based PCR chip , 2007 .

[12]  I. Mudawar,et al.  Two-phase flow in high-heat-flux micro-channel heat sink for refrigeration cooling applications: Part II—heat transfer characteristics , 2005 .

[13]  H. Lee,et al.  Pressure drop correlations for two-phase flow within horizontal rectangular channels with small heights , 2001 .

[14]  Rustem F Ismagilov,et al.  Microfluidic cartridges preloaded with nanoliter plugs of reagents: an alternative to 96-well plates for screening. , 2006, Current opinion in chemical biology.

[15]  Satish G. Kandlikar,et al.  Single-Phase Liquid Friction Factors in Microchannels , 2006 .

[16]  K. Kaler,et al.  Characteristics and impact of Taq enzyme adsorption on surfaces in microfluidic devices , 2008 .

[17]  S. Lin,et al.  Local frictional pressure drop during vaporization of R-12 through capillary tubes , 1991 .

[18]  D. Chisholm.  A theoretical basis for the Lockhart-Martinelli correlation for two-phase flow , 1967 .

[19]  Daniel A Fletcher,et al.  Unilamellar vesicle formation and encapsulation by microfluidic jetting , 2008, Proceedings of the National Academy of Sciences.

[20]  T. Hibiki,et al.  Some characteristics of air-water two-phase flow in small diameter vertical tubes , 1996 .

[21]  Freek Kapteijn,et al.  Multiphase monolith reactors: Chemical reaction engineering of segmented flow in microchannels , 2005 .

[22]  R. Shah,et al.  Laminar Flow Forced Convection in Ducts: A Source Book for Compact Heat Exchanger Analytical Data , 2014 .

[23]  Ian Papautsky,et al.  Laminar fluid behavior in microchannels using micropolar fluid theory , 1999 .

[24]  G. Whitesides,et al.  Formation of droplets and bubbles in a microfluidic T-junction-scaling and mechanism of break-up. , 2006, Lab on a chip.

[25]  Metin Muradoglu,et al.  A computational study of axial dispersion in segmented gas-liquid flow , 2007 .

[26]  D. Weitz,et al.  Monodisperse Double Emulsions Generated from a Microcapillary Device , 2005, Science.

[27]  P. Whalley,et al.  A Simple Two-Phase Frictional Pressure Drop Calculation Method , 1982 .

[28]  A. Kawahara,et al.  Investigation of two-phase flow pattern, void fraction and pressure drop in a microchannel , 2002 .

[29]  F. Bretherton.  The motion of long bubbles in tubes , 1961, Journal of Fluid Mechanics.

[30]  Saif A. Khan,et al.  Transport and reaction in microscale segmented gas-liquid flow. , 2004, Lab on a chip.

[31]  G. Mala,et al.  Pressure-driven water flows in trapezoidal silicon microchannels , 2000 .

[32]  S. Quake,et al.  Dynamic pattern formation in a vesicle-generating microfluidic device. , 2001, Physical review letters.

[33]  Dae Kun Hwang,et al.  Microfluidic-based synthesis of non-spherical magnetic hydrogel microparticles. , 2008, Lab on a chip.

[34]  Liang Li,et al.  Nanoliter microfluidic hybrid method for simultaneous screening and optimization validated with crystallization of membrane proteins , 2006, Proceedings of the National Academy of Sciences.

[35]  Clayton J. Radke,et al.  The motion of long bubbles in polygonal capillaries. Part 2. Drag, fluid pressure and fluid flow , 1995, Journal of Fluid Mechanics.