"Smart Skin" optical strain sensor using single wall carbon nanotubes

Strain measurements are essential in structural health monitoring. Traditional strain gages require physical contact between the sensor and read-out device, perturb the surface being monitored, and allow measurement only at the specific location and orientation axis of the sensor. We demonstrate a novel non-contact, multi- point, multi-directional strain sensing approach that overcomes these limitations. In our method, the surface is coated with a thin film of "smart skin" containing individualized single-walled carbon nanotubes in a polymeric host. After curing, substrate strains are transmitted through the polymer film to embedded nanotubes. This induces axial strains in the nanotubes, systematically shifting the wavelengths of their characteristic near-infrared fluorescence peaks. To measure strain, a visible laser excites nanotubes at points of interest on the surface, and the near-infrared emission is collected and spectrally analyzed. Observed spectral shifts reveal quantitative strain values. Laboratory tests show sensitivity down to ~400µm, limited by mechanical properties of the polymeric host film. We also vary excitation beam polarization to find the axis of substrate strain. Our method provides spatial resolution down to its gage length of ~100µm. Because the entire substrate is coated with nanoscale strain sensors, measurements can be made at arbitrary locations to construct a full strain map. We will describe recent smart skin refinements involving selection of polymer host, nanotube surfactant, nanotube dispersion method, and preparation protocol. Finally, we characterize the orientational distribution of nanotubes using a probabilistic model.

[1]  K. Ishibashi,et al.  Direct observation of the deformation and the band gap change from an individual single-walled carbon nanotube under uniaxial strain. , 2007, Nano letters.

[2]  Kyeongjae Cho,et al.  Chemical control of nanotube electronics , 2000 .

[3]  W. D. de Heer,et al.  Carbon Nanotubes--the Route Toward Applications , 2002, Science.

[4]  Tao Liu,et al.  A Review: Carbon Nanotube-Based Piezoresistive Strain Sensors , 2012, J. Sensors.

[5]  Satish Nagarajaiah,et al.  Strain paint: noncontact strain measurement using single-walled carbon nanotube composite coatings. , 2012, Nano letters.

[6]  P. Valavala,et al.  Self-consistent calculations of strain-induced band gap changes in semiconducting ( n , 0 ) carbon nanotubes , 2008 .

[7]  S. Iijima.  Helical microtubules of graphitic carbon , 1991, Nature.

[8]  P. Ajayan,et al.  Applications of Carbon Nanotubes , 2001 .

[9]  Lain‐Jong Li,et al.  Chirality assignment of single-walled carbon nanotubes with strain. , 2004, Physical review letters.

[10]  V. C. Moore,et al.  Band Gap Fluorescence from Individual Single-Walled Carbon Nanotubes , 2002, Science.

[11]  K. Hill,et al.  Fiber Bragg grating technology fundamentals and overview , 1997 .

[12]  Sivaram Arepalli,et al.  Strain measurements on individual single-walled carbon nanotubes in a polymer host: structure-dependent spectral shifts and load transfer. , 2008, Nano letters.

[13]  Yang,et al.  Electronic structure of deformed carbon nanotubes , 2000, Physical review letters.

[14]  J. Hone,et al.  Probing strain-induced electronic structure change in graphene by Raman spectroscopy. , 2010, Nano letters.

[15]  Markus Brink,et al.  Tuning carbon nanotube band gaps with strain. , 2003, Physical review letters.

[16]  Satish Nagarajaiah,et al.  Nanotube film based on single-wall carbon nanotubes for strain sensing , 2004 .