Effects of different surface modifications on the fatigue life of selective laser melted 15–5 PH stainless steel

[1]  N. Shamsaei,et al.  Fatigue behavior of additively manufactured 17-4 PH stainless steel: Synergistic effects of surface roughness and heat treatment , 2019, International Journal of Fatigue.

[2]  A. Nath,et al.  Effects of heat treatment and build orientations on the fatigue life of selective laser melted 15-5 PH stainless steel , 2019, Materials Science and Engineering: A.

[3]  Xiaoyan Zeng,et al.  Effect of laser remelting on deposition quality, residual stress, microstructure, and mechanical property of selective laser melting processed Ti-5Al-2.5Sn alloy , 2019, Materials Characterization.

[4]  A. Nath,et al.  Effect of Heat Treatment on Corrosion Properties of Selective Laser Melted Stainless Steel Parts , 2018, Volume 1: Additive Manufacturing; Bio and Sustainable Manufacturing.

[5]  A. Nath,et al.  Effect of Heat Treatment on Impact Toughness of Selective Laser Melted Stainless Steel Parts , 2018, Volume 1: Additive Manufacturing; Bio and Sustainable Manufacturing.

[6]  H. Asgari,et al.  Achieving low surface roughness AlSi10Mg_200C parts using direct metal laser sintering , 2018 .

[7]  A. Nath,et al.  Effect of mean stresses on mode of failures and fatigue life of selective laser melted stainless steel , 2017 .

[8]  A. Nath,et al.  Effect of Different Heat Treatments on Mechanical Properties of Laser Sintered Additive Manufactured Parts , 2017 .

[9]  A. Nath,et al.  Analysis of temperature and surface hardening of low carbon thin steel sheets using Yb-fiber laser , 2016 .

[10]  D. Wimpenny,et al.  Electropolishing of Re-melted SLM Stainless Steel 316L Parts Using Deep Eutectic Solvents: 3 × 3 Full Factorial Design , 2016, Journal of Materials Engineering and Performance.

[11]  C. Donne,et al.  Effect of surface roughness on fatigue performance of additive manufactured Ti–6Al–4V , 2016 .

[12]  T. Mower,et al.  Mechanical behavior of additive manufactured, powder-bed laser-fused materials , 2016 .

[13]  F. Walther,et al.  Computed tomography for characterization of fatigue performance of selective laser melted parts , 2015 .

[14]  Galina Kasperovich,et al.  Improvement of fatigue resistance and ductility of TiAl6V4 processed by selective laser melting , 2015 .

[15]  Konrad Wegener,et al.  Fatigue performance of additive manufactured metallic parts , 2013 .

[16]  B. Stucker,et al.  A comparison of the tensile, fatigue, and fracture behavior of Ti–6Al–4V and 15-5 PH stainless steel parts made by selective laser melting , 2013 .

[17]  J. Kruth,et al.  The investigation of the influence of laser re‐melting on density, surface quality and microstructure of selective laser melting parts , 2011 .

[18]  J. Kruth,et al.  Investigation on occurrence of elevated edges in Selective Laser Melting , 2009 .

[19]  A. Nath,et al.  Investigation on the mode of failures and fatigue life of laser-based powder bed fusion produced stainless steel parts under variable amplitude loading conditions , 2019, Additive Manufacturing.

[20]  Eckart Uhlmann,et al.  Dynamical Fatigue Behavior of Additive Manufactured Products For a Fundamental Life cycle Approach , 2017 .

[21]  Alaa Elwany,et al.  Effects of building orientation and heat treatment on fatigue behavior of selective laser melted 17-4 PH stainless steel , 2017 .

[22]  E. Abele,et al.  Fatigue Analysis in Selective Laser Melting: Review and Investigation of Thin-walled Actuator Housings , 2014 .

[23]  Ali Fatemi,et al.  Small fatigue crack growth under multiaxial stresses , 2014 .

[24]  Ashish Kumar Nath,et al.  Effect of laser operating mode in paint removal with a fiber laser , 2013 .

[25]  S. Bonss,et al.  Laser transformation hardening of steel , 2010 .

[26]  S. Suresh.  Fatigue of materials , 1991 .