Simulation of the reinforcement compaction and resin flow during the complete resin infusion process

Resin infusion (a.k.a. VARTM) is one of the LCM processes, for which liquid resin is drawn into dry reinforcements. Significant cavity thickness changes occur during processing, due to the flexibility of the vacuum bag used as one side of the tool, and the complex stress balance within the laminate. While the magnitude of thickness change is often small, the influence is significant on reinforcement properties. Changes in permeability during filling and post-filling have the potential to significantly affect the process. To simulate this behaviour, it is important to accurately model compaction and unloading of reinforcement in dry and wet states. A series of tests were completed to determine compaction behaviour of an isotropic glass fibre mat. From these tests several non-linear elastic compaction models have been determined, and applied within a resin infusion simulation which addresses pre-filling, filling and post-filling. This simulation was then used to assess different post-filling strategies.

[1]  L. J. Lee,et al.  Mold filling and curing analysis in liquid composite molding , 1993 .

[2]  John Summerscales,et al.  Resin Infusion under Flexible Tooling (RIFT): a review , 1996 .

[3]  K. Terzaghi.  Theoretical Soil Mechanics , 1943 .

[4]  Woo Il Lee,et al.  Analysis and minimization of void formation during resin transfer molding process , 2006 .

[5]  Piaras Kelly,et al.  Viscoelastic response of dry and wet fibrous materials during infusion processes , 2006 .

[6]  Rikard Gebart,et al.  Numerical model for vacuum infusion manufacturing of polymer composites , 2003 .

[7]  Constantina Lekakou,et al.  Compression in the processing of polymer composites 2. Modelling of the viscoelastic compression of resin-impregnated fibre networks , 1999 .

[8]  Z. Dimitrovová,et al.  Mesolevel analysis of the transition region formation and evolution during the liquid composite molding process , 2004 .

[9]  Suresh G. Advani,et al.  Modelling and simulation of resin transfer moulding (RTM)—gate control, venting and dry spot prediction , 1996 .

[10]  Christophe Binetruy,et al.  Simulation of LCM processes involving induced or forced deformations , 2006 .

[11]  Mathieu Devillard,et al.  Flow sensing and control strategies to address race-tracking disturbances in resin transfer molding—part II: automation and validation , 2005 .

[12]  Suresh G. Advani,et al.  Automated manufacturing environment to address bulk permeability variations and race tracking in resin transfer molding by redirecting flow with auxiliary gates , 2005 .

[13]  Simon Bickerton,et al.  Modeling and evaluation of the filling stage of injection/compression moulding , 2003 .

[14]  Suresh G. Advani,et al.  Fabric structure and mold curvature effects on preform permeability and mold filling in the RTM process. Part II. Predictions and comparisons with experiments , 2000 .

[15]  François Trochu,et al.  New Remeshing Applications in Resin Transfer Molding , 2005 .

[16]  A. Hammami,et al.  Analysis of the vacuum infusion molding process , 2000 .

[17]  Remko Akkerman,et al.  Fully 2 1/2D flow modeling of resin infusion under flexible tooling using unstructured meshes and wet and dry compaction properties , 2007 .

[18]  R. Umer,et al.  Characterising wood fibre mats as reinforcements for liquid composite moulding processes , 2007 .

[19]  Kumar K. Tamma,et al.  On a Pure Finite-Element-Based Methodology for Resin Transfer Mold (RTM) Filling Simulations. , 1999 .

[20]  François Robitaille,et al.  Compaction of textile reinforcements for composites manufacturing. II: Compaction and relaxation of dry and H2O‐saturated woven reinforcements , 1998 .

[21]  Richard S. Parnas,et al.  New set-up for in-plane permeability measurement , 2007 .

[22]  François Robitaille,et al.  Compaction of textile reinforcements for composites manufacturing. III: Reorganization of the fiber network , 1999 .

[23]  D. Bhattacharyya,et al.  Exploring the Non-Elastic Compression Deformation of Dry Glass Fibre Reinforcements , 2007 .

[24]  Woo Il Lee,et al.  Analysis of vacuum bag resin transfer molding process , 2001 .

[25]  C. Binetruy,et al.  Unidirectional compression of fibre reinforcements. Part 1: A non-linear elastic-plastic behaviour , 2007 .

[26]  Timothy G. Gutowski,et al.  The Consolidation of Laminate Composites , 1987 .

[27]  A. Long,et al.  Active control of the vacuum infusion process , 2007 .

[28]  François Robitaille,et al.  Compaction of textile reinforcements for composites manufacturing. I: Review of experimental results , 1998 .

[29]  R. Byron Pipes,et al.  Flow and Compaction During the Vacuum Assisted Resin Transfer Molding Process , 2001 .

[30]  S. Advani,et al.  Characterization and modeling of race-tracking in liquidcomposite molding processes , 1999 .

[31]  S. Advani,et al.  Correlation of void distribution to VARTM manufacturing techniques , 2007 .

[32]  François Trochu,et al.  Numerical simulation of resin infusion and reinforcement consolidation under flexible cover , 2005 .

[33]  Andrew C. Long,et al.  Analysis of the vacuum infusion moulding process: I. Analytical formulation , 2005 .

[34]  Bekir Yenilmez,et al.  Variation of part thickness and compaction pressure in vacuum infusion process , 2009 .

[35]  Simon Bickerton,et al.  Compression flow permeability measurement: a continuous technique , 2003 .

[36]  François Trochu,et al.  Concurrent methods for permeability measurement in resin transfer molding , 1996 .

[37]  Piaras Kelly,et al.  Full field monitoring of the resin flow and laminate properties during the resin infusion process , 2008 .

[38]  Determining the 3D permeability of fibrous media using the Newton method , 2005 .

[39]  Suresh G. Advani,et al.  Desirable features in mold filling simulations for Liquid Composite Molding processes , 2004 .

[40]  Hoon Huh,et al.  A finite element simulation of resin transfer molding based on partial nodal saturation and implicit time integration , 1998 .

[41]  Suresh G. Advani,et al.  Modeling resin flow and fiber tow saturation induced by distribution media collapse in VARTM , 2007 .

[42]  Hugo Sol,et al.  Permeability measurement of textile reinforcements with several test fluids , 2001 .

[43]  Suresh G. Advani,et al.  Simultaneous gate and vent location optimization in liquid composite molding processes , 2004 .