A simple composite protective layer coating that enhances the cycling stability of lithium metal batteries

Abstract Metallic lithium is the most promising negative electrode for high-energy rechargeable batteries due to its extremely high specific capacity and its extremely low redox potential. However, the low cycle efficiency and lithium dendrite formation during the charge/discharge processes consistently hinder its practical application. In this report, we present a stabilized Li electrode on which a Li + ion conductive inorganic/organic composite protective layer (CPL) is coated. With the introduction of the CPL, the Li dendrite growth and electrolyte decomposition are effectively suppressed; consequently, stable Li plating/stripping at high current densities up to 10 mA cm −2 is possible. Nanoindentation tests demonstrate that the shear modulus of the CPL at narrow indentations is 1.8 times higher than that of the Li metal, which provides a theoretical understanding for its efficacy. Moreover, the LiCoO 2 /Li cell incorporating CPL exhibits excellent cycling stability up to 400 cycles at 1 mA cm −2 (1 C-rate), which demonstrates practical applicability in Li ion batteries through replacing the graphite anode with a CPL-coated Li metal anode.

[1]  Doron Aurbach,et al.  A short review of failure mechanisms of lithium metal and lithiated graphite anodes in liquid electrolyte solutions , 2002 .

[2]  B. Liaw,et al.  A review of lithium deposition in lithium-ion and lithium metal secondary batteries , 2014 .

[3]  K. Edström,et al.  The SEI layer formed on lithium metal in the presence of oxygen: A seldom considered component in the development of the Li–O2 battery , 2013 .

[4]  D. J. Lee,et al.  Enhanced cycling performance of lithium metal secondary batteries with succinic anhydride as an electrolyte additive , 2014 .

[5]  Dongmin Im,et al.  A Highly Reversible Lithium Metal Anode , 2014, Scientific Reports.

[6]  Yang-Kook Sun,et al.  Challenges facing lithium batteries and electrical double-layer capacitors. , 2012, Angewandte Chemie.

[7]  Yuki Kato,et al.  A lithium superionic conductor. , 2011, Nature materials.

[8]  T. Homma,et al.  In Situ Observation of Dendrite Growth of Electrodeposited Li Metal , 2010 .

[9]  B. Scrosati,et al.  The Li/LiV3O8 polymer electrolyte lithium battery III. Investigation of the electrode interfaces , 1988 .

[10]  Rachid Meziane,et al.  Single-ion BAB triblock copolymers as highly efficient electrolytes for lithium-metal batteries. , 2013, Nature materials.

[11]  Yong-Kook Choi,et al.  Lithium phosphorous oxynitride as a passive layer for anodes in lithium secondary batteries , 2004 .

[12]  J. Whitacre,et al.  Chemical stability enhancement of lithium conducting solid electrolyte plates using sputtered LiPON thin films , 2004 .

[13]  W. Meyer,et al.  Polymer electrolytes for lithium-ion batteries. , 1998, Advanced materials.

[14]  Noboru Oyama,et al.  Inhibition effects of polyacrylonitrile gel electrolytes on lithium dendrite formation , 1999 .

[15]  Bruno Scrosati,et al.  Moving to a Solid‐State Configuration: A Valid Approach to Making Lithium‐Sulfur Batteries Viable for Practical Applications , 2010, Advanced materials.

[16]  D. J. Lee,et al.  Chemical aspect of oxygen dissolved in a dimethyl sulfoxide-based electrolyte on lithium metal , 2014 .

[17]  Charles W. Monroe,et al.  The Impact of Elastic Deformation on Deposition Kinetics at Lithium/Polymer Interfaces , 2005 .

[18]  B. Dunn,et al.  Protection of lithium metal surfaces using tetraethoxysilane , 2011 .

[19]  M. Armand,et al.  Building better batteries , 2008, Nature.

[20]  Jean-Marie Tarascon,et al.  Li-O2 and Li-S batteries with high energy storage. , 2011, Nature materials.

[21]  Chongdu Cho,et al.  Effect of gas-diffusion electrode material heterogeneity on the structural integrity of polymer elec , 2010 .

[22]  H. Tamura,et al.  X-ray photoelectron spectroscopic analysis and scanning electron microscopic observation of the lithium surface immersed in nonaqueous solvents , 1994 .

[23]  G. M. Rao,et al.  Chemical and microstructural modifications in LiPON thin films exposed to atmospheric humidity , 2011 .

[24]  B. Scrosati,et al.  Lithium batteries: Status, prospects and future , 2010 .

[25]  M. Armand,et al.  Issues and challenges facing rechargeable lithium batteries , 2001, Nature.

[26]  D. J. Lee,et al.  Composite protective layer for Li metal anode in high-performance lithium–oxygen batteries , 2014 .

[27]  Kevin G. Gallagher,et al.  Quantifying the promise of lithium–air batteries for electric vehicles , 2014 .

[28]  Myung-Hyun Ryou,et al.  Excellent Cycle Life of Lithium‐Metal Anodes in Lithium‐Ion Batteries with Mussel‐Inspired Polydopamine‐Coated Separators , 2012 .

[29]  Ji‐Guang Zhang,et al.  Lithium metal anodes for rechargeable batteries , 2014 .

[30]  D. Aurbach.  Review of selected electrode–solution interactions which determine the performance of Li and Li ion batteries , 2000 .

[31]  Doron Aurbach,et al.  Recent studies of the lithium-liquid electrolyte interface Electrochemical, morphological and spectral studies of a few important systems , 1995 .