Nanomechanical behavior and structural stability of a nanocrystalline CoCrFeNiMn high-entropy alloy processed by high-pressure torsion

A CoCrFeNiMn high-entropy alloy (HEA), in the form of a face-centered cubic (fcc) solid solution, was processed by high-pressure torsion (HPT) to produce a nanocrystalline (nc) HEA. Significant grain refinement was achieved from the very early stage of HPT through 1/4 turn and an nc structure with an average grain size of ∼40 nm was successfully attained after 2 turns. The feasibility of significant microstructural changes was attributed to the occurrence of accelerated atomic diffusivity under the torsional stress during HPT. Nanoindentation experiments showed that the hardness increased significantly in the nc HEA during HPT processing and this was associated with additional grain refinement. The estimated values of the strain-rate sensitivity were maintained reasonably constant from the as-cast condition to the nc alloy after HPT through 2 turns, thereby demonstrating a preservation of plasticity in the HEA. In addition, a calculation of the activation volume suggested that the grain boundaries play an important role in the plastic deformation of the nc HEA where the flow mechanism is consistent with other nc metals. Transmission electron microscopy showed that, unlike conventional fcc nc metals, the nc HEA exhibits excellent microstructural stability under severe stress conditions.

[1]  R. Valiev,et al.  Structure and deformaton behaviour of Armco iron subjected to severe plastic deformation , 1996 .

[2]  Terence G. Langdon,et al.  Using high-pressure torsion for metal processing: Fundamentals and applications , 2008 .

[3]  Juyoung Kim,et al.  Nanoscale room temperature creep of nanocrystalline nickel pillars at low stresses , 2013 .

[4]  Warren C. Oliver,et al.  Indentation power-law creep of high-purity indium , 1999 .

[5]  N. Stepanov,et al.  Effect of cryo-deformation on structure and properties of CoCrFeNiMn high-entropy alloy , 2015 .

[6]  T. Nieh,et al.  Effects of Al addition on structural evolution and tensile properties of the FeCoNiCrMn high-entropy alloy system , 2014 .

[7]  A. Kuznetsov,et al.  Effect of Mn and V on structure and mechanical properties of high-entropy alloys based on CoCrFeNi system , 2014 .

[8]  Subra Suresh,et al.  Some critical experiments on the strain-rate sensitivity of nanocrystalline nickel , 2003 .

[9]  K. Lu,et al.  Hardness and strain rate sensitivity of nanocrystalline Cu , 2006 .

[10]  T. Langdon.  Twenty-five years of ultrafine-grained materials: achieving exceptional properties through grain refinement , 2013 .

[11]  Robert J. Asaro,et al.  Toward a quantitative understanding of mechanical behavior of nanocrystalline metals , 2007 .

[12]  G. Pharr,et al.  Extraction of flow properties of single crystal silicon carbide by nanoindentation and finite element simulation , 2008 .

[13]  T. Nieh,et al.  In-situ neutron diffraction study of deformation behavior of a multi-component high-entropy alloy , 2014 .

[14]  Jien-Wei Yeh,et al.  Fatigue behavior of Al0.5CoCrCuFeNi high entropy alloys , 2012 .

[15]  B. S. Murty,et al.  Processing and properties of nanocrystalline CuNiCoZnAlTi high entropy alloys by mechanical alloying , 2010 .

[16]  T. Langdon,et al.  Enhancement of strain-rate sensitivity and shear yield strength of a magnesium alloy processed by high-pressure torsion , 2015 .

[17]  B. Murty,et al.  Alloying behavior in multi-component AlCoCrCuFe and NiCoCrCuFe high entropy alloys , 2012 .

[18]  T. Langdon,et al.  The significance of strain reversals during processing by high-pressure torsion , 2008 .

[19]  T. Langdon,et al.  Using finite element modeling to examine the temperature distribution in quasi-constrained high-pressure torsion , 2012 .

[20]  T. Shun,et al.  Nanostructured High‐Entropy Alloys with Multiple Principal Elements: Novel Alloy Design Concepts and Outcomes , 2004 .

[21]  T. Langdon,et al.  Evolution of plasticity, strain-rate sensitivity and the underlying deformation mechanism in Zn–22% Al during high-pressure torsion , 2014 .

[22]  D. H. Wen,et al.  Nanoindentation creep behavior in a CoCrFeCuNi high-entropy alloy film with two different structure states , 2015 .

[23]  G. Eggeler,et al.  The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy , 2013 .

[24]  R. Valiev,et al.  Nanostructuring of metals by severe plastic deformation for advanced properties , 2004, Nature materials.

[25]  U. Ramamurty,et al.  Nanoindentation behavior of nanotwinned Cu: Influence of indenter angle on hardness, strain rate sensitivity and activation volume , 2013 .

[26]  Jing Shi,et al.  Nanocrystalline CoCrFeNiCuAl high-entropy solid solution synthesized by mechanical alloying , 2009 .

[27]  X. Liao,et al.  Hardening of an Al0.3CoCrFeNi high entropy alloy via high-pressure torsion and thermal annealing , 2015 .

[28]  Jien-Wei Yeh,et al.  High-Entropy Alloys: Basic Concepts , 2014 .

[29]  G. Eggeler,et al.  Temperature dependencies of the elastic moduli and thermal expansion coefficient of an equiatomic, single-phase CoCrFeMnNi high-entropy alloy , 2015 .

[30]  B. Cantor,et al.  Microstructural development in equiatomic multicomponent alloys , 2004 .

[31]  G. Pharr,et al.  Temperature dependence of the mechanical properties of equiatomic solid solution alloys with face-centered cubic crystal structures , 2014 .

[32]  M. Meyers,et al.  Mechanical properties of nanocrystalline materials , 2006 .

[33]  J. Yeh,et al.  Structural and Thermodynamic Factors of Suppressed Interdiffusion Kinetics in Multi-component High-entropy Materials , 2014, Scientific Reports.

[34]  Y. Estrin,et al.  Short-circuit diffusion in an ultrafine-grained copper-zirconium alloy produced by equal channel angular pressing , 2007 .

[35]  Jien-Wei Yeh,et al.  High-Entropy Alloys , 2014 .

[36]  A. Hamza,et al.  Temperature-dependent strain rate sensitivity and activation volume of nanocrystalline Ni , 2006 .

[37]  Q. Guan,et al.  Finite Element Analysis of High Pressure Torsion Processing , 2011 .

[38]  Ting Zhu,et al.  Ultra-strength materials , 2010 .

[39]  Y. Estrin,et al.  Nano- and micro-scale free volume in ultrafine grained Cu-1 wt.%Pb alloy deformed by equal channel angular pressing , 2009 .

[40]  H. Conrad.  Grain size dependence of the plastic deformation kinetics in Cu , 2003 .

[41]  T. Langdon,et al.  A comparison of microstructures and mechanical properties in a Cu–Zr alloy processed using different SPD techniques , 2013, Journal of Materials Science.

[42]  Maria Dolors Baró,et al.  Experimental parameters influencing grain refinement and microstructural evolution during high-pressure torsion , 2003 .

[43]  J. Weertman,et al.  Rapid stress-driven grain coarsening in nanocrystalline Cu at ambient and cryogenic temperatures , 2005 .

[44]  T. G. Nieh,et al.  Creep of nanocrystalline nickel: A direct comparison between uniaxial and nanoindentation creep , 2010 .

[45]  T. Nieh,et al.  Incipient plasticity and dislocation nucleation of FeCoCrNiMn high-entropy alloy , 2013 .

[46]  T. G. Nieh,et al.  Grain growth and the Hall–Petch relationship in a high-entropy FeCrNiCoMn alloy , 2013 .

[47]  R. Valiev,et al.  Principles of equal-channel angular pressing as a processing tool for grain refinement , 2006 .

[48]  Y. Estrin,et al.  Percolating network of ultrafast transport channels in severely deformed nanocrystalline metals , 2009 .

[49]  K. Edalati,et al.  High-pressure torsion for enhanced atomic diffusion and promoting solid-state reactions in the aluminum–copper system , 2013 .

[50]  M. Kawasaki.  Different models of hardness evolution in ultrafine-grained materials processed by high-pressure torsion , 2013, Journal of Materials Science.

[51]  J. Yeh,et al.  Sluggish diffusion in Co-Cr-Fe-Mn-Ni high-entropy alloys , 2013 .

[52]  J. C. Huang,et al.  Grain-boundary strengthening in nanocrystalline chromium and the Hall–Petch coefficient of body-centered cubic metals , 2013 .

[53]  Ting Zhu,et al.  Interfacial plasticity governs strain rate sensitivity and ductility in nanostructured metals , 2007, Proceedings of the National Academy of Sciences.

[54]  K. Ramesha,et al.  Effect of nanocrystalline and ultrafine grain sizes on the strain rate sensitivity and activation volume : fcc versus bcc metals , 2004 .

[55]  Andrew M. Minor,et al.  Direct observation of deformation-induced grain growth during the nanoindentation of ultrafine-grained Al at room temperature , 2004 .

[56]  T. Langdon,et al.  Modeling the temperature rise in high-pressure torsion , 2014 .

[57]  Y. Estrin,et al.  Ultra-fast diffusion channels in pure Ni severely deformed by equal-channel angular pressing , 2011 .

[58]  T. Langdon,et al.  Rapid synthesis of an extra hard metal matrix nanocomposite at ambient temperature , 2015 .

[59]  S. Suresh,et al.  Mechanistic models for the activation volume and rate sensitivity in metals with nanocrystalline grains and nano-scale twins , 2005 .

[60]  H. Kanayama,et al.  Significance of temperature increase in processing by high-pressure torsion , 2011 .

[61]  H. Conrad.  Plastic deformation kinetics in nanocrystalline FCC metals based on the pile-up of dislocations , 2007 .

[62]  K. Dahmen,et al.  Microstructures and properties of high-entropy alloys , 2014 .

[63]  Hongsheng Gao,et al.  High-pressure torsion-induced grain growth in electrodeposited nanocrystalline Ni , 2006 .

[64]  Jien-Wei Yeh,et al.  Microstructure and texture evolution during annealing of equiatomic CoCrFeMnNi high-entropy alloy , 2014 .

[65]  T. Langdon,et al.  Using finite element modeling to examine the flow processes in quasi-constrained high-pressure torsion , 2011 .

[66]  M. Koizumi,et al.  Effect of high pressure on interdiffusion in an Al-Mg alloy , 1983 .

[67]  Yucheng Wang,et al.  Alloying behavior and novel properties of CoCrFeNiMn high-entropy alloy fabricated by mechanical alloying and spark plasma sintering , 2015 .

[68]  Philippe Spätig,et al.  Deformation behaviour and microstructure of nanocrystalline electrodeposited and high pressure torsioned nickel , 2005 .

[69]  E. Ma.  Watching the Nanograins Roll , 2004, Science.

[70]  G. Pharr,et al.  An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments , 1992 .

[71]  C. Woodward,et al.  Microstructure and elevated temperature properties of a refractory TaNbHfZrTi alloy , 2012, Journal of Materials Science.

[72]  Kai Zhang,et al.  The influence of time, temperature, and grain size on indentation creep in high-purity nanocrystalline and ultrafine grain copper , 2004 .

[73]  T. Langdon,et al.  Orientation imaging microscopy of ultrafine-grained nickel , 2002 .