Effects of Cracks on the Mass Transfer of Polymer Electrolyte Membrane Fuel Cell with High Performance Membrane Electrode Assembly

[1]  Junliang Zhang,et al.  Flow field design with 3D geometry for proton exchange membrane fuel cells , 2019, Applied Thermal Engineering.

[2]  M. Pritzker,et al.  Investigation of catalyst layer defects in catalyst‐coated membrane for PEMFC application: Non‐destructive method , 2018, International Journal of Energy Research.

[3]  M. Pan,et al.  Determination of oxygen transport resistance in gas diffusion layer for polymer electrolyte fuel cells , 2018 .

[4]  B. Yi,et al.  Nano-engineering of a 3D-ordered membrane electrode assembly with ultrathin Pt skin on open-walled PdCo nanotube arrays for fuel cells , 2018 .

[5]  Guobin Zhang,et al.  Three-Dimensional Simulation of Water Management for High-Performance Proton Exchange Membrane Fuel Cell , 2018 .

[6]  M. Pan,et al.  Effect of hydrophobic additive on oxygen transport in catalyst layer of proton exchange membrane fuel cells , 2018 .

[7]  Chao-Yang Wang,et al.  Modeling two-phase flow in three-dimensional complex flow-fields of proton exchange membrane fuel cells , 2017 .

[8]  A. Bazylak,et al.  Non-isothermal two-phase transport in a polymer electrolyte membrane fuel cell with crack-free microporous layers , 2017 .

[9]  Koichi Kojima,et al.  Current Status and Future Outlook of Fuel Cell Vehicle Development in Toyota , 2015 .

[10]  Zeyun Jiang,et al.  Flow properties of an intact MPL from nano-tomography and pore network modelling , 2014 .

[11]  C. Arcoumanis,et al.  Degradation aspects of water formation and transport in Proton Exchange Membrane Fuel Cell: A review , 2013 .

[12]  Shohji Tsushima,et al.  Observation of dynamic liquid water transport in the microporous layer and gas diffusion layer of an operating PEM fuel cell by high-resolution soft X-ray radiography , 2013 .

[13]  T. Schubert,et al.  Enhancement of proton exchange membrane fuel cell performance by doping microporous layers of gas diffusion layers with multiwall carbon nanotubes , 2012 .

[14]  S. H. Kim,et al.  Improvement of the mechanical durability of micro porous layer in a proton exchange membrane fuel cell by elimination of surface cracks , 2012 .

[15]  Shengmin Guo,et al.  CFD analysis of a PEM fuel cell for liquid dispersion at the interface of GDL‐GFC , 2011 .

[16]  Shohji Tsushima,et al.  Soft X-ray visualization of the liquid water transport within the cracks of micro porous layer in PEMFC , 2011 .

[17]  Emin Caglan Kumbur,et al.  Characterization of interfacial morphology in polymer electrolyte fuel cells: Micro-porous layer and catalyst layer surfaces , 2010 .

[18]  Xianguo Li,et al.  On the modeling of water transport in polymer electrolyte membrane fuel cells , 2009 .

[19]  Jinsheng Xiao,et al.  Gas diffusion through differently structured gas diffusion layers of PEM fuel cells , 2007 .

[20]  Jinsheng Xiao,et al.  Effects of porosity distribution variation on the liquid water flux through gas diffusion layers of PEM fuel cells , 2006 .

[21]  Jian Zhang,et al.  Effects of MEA preparation on the performance of a direct methanol fuel cell , 2006 .

[22]  Chao-Yang Wang,et al.  A Nonisothermal, Two-Phase Model for Polymer Electrolyte Fuel Cells , 2006 .

[23]  Zhigang Qi,et al.  Improvement of water management by a microporous sublayer for PEM fuel cells , 2002 .