Microscale interpretation of tribological phenomena in Ti/TiN soft-hard multilayer coatings on soft austenite steel substrates

The mechanical and tribological behavior of physical vapor deposited coatings on soft substrate materials gains increasing interest due to economical and environmental aspects – e.g. substitution of steels by light-weight metals or polymers in transport vehicles. Nevertheless, such soft materials require surface protection against wear in tribological contacts. Single layer hard coatings deposited at room temperature are brittle with a relatively poor adhesion. Therefore, they should be better substituted by tough multilayer coatings of soft-hard material combinations. However, the mechanics of such multilayer coatings with several 10 nm thick bilayer periods is difficult and yet not well described. The presented work tries to fill the gap of knowledge by focusing both on mechanical investigations of hardness, adhesion, and wear and on microscopic elucidation of deformation mechanisms. In the paper 1 μm thick Ti/TiN multilayer stacks were deposited by magnetron sputtering on soft austenitic steel substrates at room temperature to prevent distortion of functional components in future applications. High hardness was found for 8 and 16 bilayer films with modulation ratio Ti:TiN = 1:2 and 1:4. This was attributed (with use of transmission electron microscopy) to stopping the crack propagation in thin Ti layers of the multilayer systems by shear deformation combined with different fracture mechanisms in comparison with that for the TiN single layers (edge cracks at the border of the contact area and ring cracks outside, respectively).

[1]  Richard D. Jones,et al.  Modelling the Deformation Behaviour of Multilayer Coatings , 2001 .

[2]  M. Sebastiani,et al.  High thickness Ti/TiN multilayer thin coatings for wear resistant applications , 2006 .

[3]  A. Matthews,et al.  Handbook of Hard Coatings: Edited by Rointan E Bunshah; Noyes Publications/William Andrew Publishing, New York 2001 (Available from American Technical Publishers Ltd, 27-29 Knowl Piece, Wilbury Way, Hitchin, Herts, SG4 0SX, England, Price £94) , 2001 .

[4]  D. Kwon,et al.  Analysis of interfacial strengthening from composite hardness of TiN/VN and TiN/NbN multilayer hard coatings , 2004 .

[5]  C. Ziebert,et al.  Improvement of Hardness and Toughness of TiAlN Coating by Nanoscale Multilayered Structurization with Si3N4 , 2007 .

[6]  J. Duh,et al.  Effect of heat treatment on mechanical properties and microstructure of CrN/AlN multilayer coatings , 2006 .

[7]  Michael V. Swain,et al.  INDENTATION RESPONSE AND CRACKING OF SUB-MICRON SILICA FILMS ON A POLYMERIC SUBSTRATE , 1998 .

[8]  S. Jacobson,et al.  The multilayer effect in abrasion — optimising the combination of hard and tough phases , 1999 .

[9]  W. Kao,et al.  Optimum multilayer TiN–TiCN coatings for wear resistance and actual application , 1998 .

[10]  G. Abadias,et al.  Nanoindentation hardness and structure of ion beam sputtered TiN, W and TiN/W multilayer hard coatings , 2006 .

[11]  M. Larsson,et al.  Wear resistance of multilayered PVD TiN/TaN on HSS , 1999 .

[12]  J. Hosson,et al.  Breakdown of the Coulomb friction law in TiC∕a‐C:H nanocomposite coatings , 2006 .

[13]  E. Martínez,et al.  Multilayered chromium/chromium nitride coatings for use in pressure die-casting , 2001 .

[14]  B. Lawn.  Fracture and deformation in brittle solids: A perspective on the issue of scale , 2004 .

[15]  M. Larsson,et al.  Wear of PVD Ti/TiN multilayer coatings , 1997 .

[16]  K. Zdunek,et al.  Investigation of adhesion between component layers of a multi-layer coating TiC/Ti(Cx, N1−x)/TiN by the scratch-test method , 1999 .

[17]  B. Lawn,et al.  Role of adhesive interlayer in transverse fracture of brittle layer structures , 2000 .

[18]  E. Martínez,et al.  Wear behavior of nanometric CrN/Cr multilayers , 2003 .

[19]  A. Matthews.  Developments in PVD tribological coatings (IUVSTA highlights seminar-vacuum metallurgy division) , 2002 .

[20]  E. Hall,et al.  The Deformation and Ageing of Mild Steel , 1951 .

[21]  M. Odén,et al.  Characterization of the Induced Plastic Zone in a Single Crystal TiN(001) Film by Nanoindentation and Transmission Electron Microscopy , 1997 .

[22]  P. Psyllaki,et al.  Elaboration and characterization of Ti and TiN thin films and Ti/TiN multilayers for hard coating applications , 1996 .

[23]  S. S. Eskildsen,et al.  Engineering applications for diamond-like carbon , 1994 .

[24]  J. Musil.  Hard and superhard nanocomposite coatings , 2000 .

[25]  M. T. Vieira,et al.  The influence of ductile interlayers on the mechanical performance of tungsten nitride coatings , 1999 .

[26]  Brian R. Lawn,et al.  Fracture modes in brittle coatings with large interlayer modulus mismatch , 1999 .

[27]  H. Holleck,et al.  Multilayer PVD coatings for wear protection , 1995 .

[28]  Response to loading and stiffness of coated substrates indented by spheres , 2005 .

[29]  B. Lawn,et al.  Cracking of brittle coatings adhesively bonded to substrates of unlike modulus , 2000 .

[30]  Kenneth Holmberg,et al.  Coatings tribology: a concept, critical aspects and future directions , 1994 .

[31]  C. Ziebert,et al.  Concepts for the design of advanced nanoscale PVD multilayer protective thin films , 2009 .

[32]  A. Traverse,et al.  Ion beam mixing of and multilayers , 1990 .

[33]  M. D. Thouless,et al.  Growth and configurational stability of circular, buckling-driven film delaminations , 1992 .

[34]  E. G. Herbert,et al.  On the Measurement of Stress-Strain Curves by Spherical Indentation , 2000 .

[35]  K. Ludema,et al.  Wear of materials , 1977 .

[36]  M. Griepentrog,et al.  Ti/TiN multilayer coatings: deposition technique, characterization and mechanical properties , 2001 .

[37]  J. Hahn,et al.  Synthesis of CrN/AlN superlattice coatings using closed-field unbalanced magnetron sputtering process , 2003 .

[38]  Sam Zhang,et al.  Nanocomposite thin films and coatings : processing, properties and performance , 2007 .

[39]  C. S. Bhatia,et al.  Nanoindentation and nanoscratching of hard carbon coatings for magnetic disks , 1995 .

[40]  Je-hyun Lee,et al.  Effects of the thickness of Ti buffer layer on the mechanical properties of TiN coatings , 2003 .

[41]  Y. Wang,et al.  Fracture mechanisms in nanoscale layered hard thin films , 2002 .

[42]  Johann Michler,et al.  Analysis of coating fracture and substrate plasticity induced by spherical indentors: diamond and diamond-like carbon layers on steel substrates , 2001 .

[43]  A. Evans,et al.  Crack deflection at an interface between dissimilar elastic materials: Role of residual stresses , 1994 .

[44]  J. Lackner.  Industrially-scaled room-temperature pulsed laser deposition of Ti-TiN multilayer coatings , 2007 .

[45]  Vassilis Kostopoulos,et al.  3-D Modeling of nanoindentation experiment on a coating-substrate system , 2001 .

[46]  M. Larsson,et al.  Mechanical and tribological properties of multilayered PVD TiN/CrN , 1999 .

[47]  Kenneth Holmberg,et al.  Coatings tribology—contact mechanisms and surface design , 1997 .

[48]  S. Mukamel,et al.  Multidimensional Infrared Signatures of Intramolecular Hydrogen Bonding in Malonaldehyde , 2003 .

[49]  J. Hutchinson,et al.  Cracking and stress redistribution in ceramic layered composites , 1993 .

[50]  S. Lehoczky.  Retardation of Dislocation Generation and Motion in Thin-Layered Metal Laminates , 1978 .

[51]  E. Hall,et al.  The Deformation and Ageing of Mild Steel: III Discussion of Results , 1951 .

[52]  A. Matthews,et al.  Design criteria for wear-resistant nanostructured and glassy-metal coatings , 2004 .

[53]  A. Matthews,et al.  On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimised tribological behaviour , 2000 .

[54]  K. Holmberg.  Coatings Tribology: Properties, Techniques and Applications in Surface Engineering , 1994 .

[55]  Michael V. Swain,et al.  Investigation of the stresses and stress intensity factors responsible for fracture of thin protective films during ultra-micro indentation tests with spherical indenters , 1996 .

[56]  John W. Hutchinson,et al.  Crack deflection at an interface between dissimilar elastic-materials , 1989 .

[57]  J. Hosson,et al.  Deformation mechanisms in TiN/(Ti,Al)N multilayers under depth-sensing indentation , 2006 .

[58]  M. Kot,et al.  Effect of bilayer period on properties of Cr/CrN multilayer coatings produced by laser ablation , 2008 .

[59]  李幼升,et al.  Ph , 1989 .

[60]  Philip J. Martin,et al.  Deformation mechanisms of TiN multilayer coatings alternated by ductile or stiff interlayers , 2008 .

[61]  J. Esteve,et al.  Period dependence of hardness and microstructure on nanometric Cr/CrN multilayers , 2004 .

[62]  Sture Hogmark,et al.  Mechanical and tribological properties of multilayered PVD TiN/CrN, TiN/MoN, TiN/NbN and TiN/TaN coatings on cemented carbide , 1998 .

[63]  B. Lawn,et al.  Indentation fracture: principles and applications , 1975 .

[64]  A. C. Fischer-Cripps,et al.  Critical review of analysis and interpretation of nanoindentation test data , 2006 .

[65]  G. Stachowiak.  Wear - Materials, Mechanisms and Practice: Stachowiak/Wear - Materials, Mechanisms and Practice , 2005 .

[66]  A. Matthews,et al.  Thick Ti/TiN multilayered coatings for abrasive and erosive wear resistance , 1994 .

[67]  J. Schneider,et al.  Multilayer composite ceramicmetal-DLC coatings for sliding wear applications , 1996 .

[68]  Leon M Keer,et al.  An extension of the Hertz theory for 2D coated components , 2005 .

[69]  Z. Farhat,et al.  Nanoindentation and friction studies on Ti-based nanolaminated films , 1997 .

[70]  K. Ma,et al.  Examination of mechanical properties and failure mechanisms of TiN and Ti−TiN multilayer coatings , 1995 .

[71]  K. Holmberg,et al.  Design aspects for advanced tribological surface coatings , 1998 .

[72]  M. Tilbrook,et al.  Microstructural effects on indentation failure mechanisms in TiN coatings: Finite element simulations , 2007 .

[73]  Yujuan Wu,et al.  Hertzian contact response of single-layer, functionally graded and sandwich coatings , 2007 .

[74]  J. Esteve,et al.  Nanoindentation stress–strain curves as a method for thin-film complete mechanical characterization: application to nanometric CrN/Cr multilayer coatings , 2003 .

[75]  B. Lawn,et al.  Overview: Damage in brittle layer structures from concentrated loads , 2002 .

[76]  C. Teichert,et al.  Mechanisms for self-assembling topography formation in low-temperature vacuum deposition of inorganic coatings on polymer surfaces , 2010 .

[77]  K. Zdunek,et al.  Effect of interlayer composition on the tribological properties of TiC/Ti(Cx, N1−x)/TiN anti-abrasive multi-layer coatings , 1999 .