Heat affected zones in polymer laser marking

Laser marking is based on the laser heating of the subjected material, the heating being below the melting temperature or thermal degradation starting point. Within and nearby the mark, the material is chemically, physically and mechanically affected. This means that the main characteristics are changing in such a way that the material is ageing. Thermal and mechanical analysis can be used to determine the modification of the material, which is important and necessary to know for predicting its use lifetime. This paper investigates the physical and mechanical modification of the polymer HDPE100, when laser marking is applied. Burst stress, elongation and relaxation modulus were determined for the base material, within the heat affected zone and within the laser burned mark. Information on the crystallization rate and on the elongation viscosity is also reported. According to the results, the polyethylene has very fast crystallization and that affects the marking process if lower than appropriate maintaining during heating process is applied. It becomes stabile after 0.23 min, when it is tested at 103 °C. The elongation viscosity was analysed and values of 105 Pa s were recorded for 10 s, which is a usual time of applying pressure. The performed analysis revealed about 10 % difference between the relaxation modulus of the irradiated and non-irradiated HDPE.

[1]  D. Soong,et al.  Time‐dependent rheological properties and transient structural states of entangled polymeric liquids—A kinetic network model , 1981 .

[2]  R. Avolio,et al.  Effect of compatibilization on thermal degradation kinetics of HDPE-based composites containing cellulose reinforcements , 2010 .

[3]  G. Cavallaro,et al.  Determining the selective impregnation of waterlogged archaeological woods with poly(ethylene) glycols mixtures by differential scanning calorimetry , 2013, Journal of Thermal Analysis and Calorimetry.

[4]  A. Mianowski,et al.  Analysis of relative rate of reaction/process , 2012, Journal of Thermal Analysis and Calorimetry.

[5]  P. K. Gallagher,et al.  Handbook of thermal analysis and calorimetry , 1998 .

[6]  J. Kučerík,et al.  FT-IR study of gamma-radiation induced degradation of polyvinyl alcohol (PVA) and PVA/humic acids blends , 2010 .

[7]  M. Allmen,et al.  Laser-beam interactions with materials : physical principles and applications , 1987 .

[8]  V. Velebný,et al.  Response to "A note on an alternative DSC approach to study hydration of hyaluronan". , 2013, Carbohydrate polymers.

[9]  Walter Koechner,et al.  Solid-State Laser Engineering , 1976 .

[10]  S. Vyazovkin,et al.  Activation energies of water vaporization from the bulk and from laponite, montmorillonite, and chitosan powders , 2011 .

[11]  R. B. Prime,et al.  Thermal Analysis of Polymers , 2009 .

[12]  M. Csele,et al.  Fundamentals of Light Sources and Lasers: Csele/Lights and Lasers , 2004 .

[13]  V. Mathot.  Crystallization of polymers , 2010 .

[14]  Long Jiang,et al.  Thermal, mechanical and rheological properties of polylactide toughened by expoxidized natural rubber , 2013 .

[15]  A. Behravesh,et al.  Experimental investigation on reprocessing of extruded wood flour/HDPE composites , 2012 .

[16]  G. Lazzara,et al.  Temperature-responsive inclusion complex of cationic PNIPAAM diblock copolymer and gamma-cyclodextrin , 2012 .

[17]  L. F. Vales,et al.  Bidimensional codes recorded on an oxide glass surface using a continuous wave CO2 laser , 2011 .

[18]  Rui L. Reis,et al.  Viscoelastic behaviour and time–temperature correspondence of HDPE with varying levels of process-induced orientation , 2001 .

[19]  A. Rotaru,et al.  DSC study on hyaluronan drying and hydration , 2011 .

[20]  D. Savu,et al.  Microstructure of magnetite doped elastomers investigated by SAXS and SANS , 2008 .

[21]  J. Kučerík,et al.  A hint on the correlation between cellulose fibers polymerization degree and their thermal and thermo-oxidative degradation , 2012, Journal of Thermal Analysis and Calorimetry.

[22]  R. Bruce Prime,et al.  Thermal analysis of polymers : fundamentals and applications , 2009 .

[23]  W. Emmerich,et al.  Polymer characterization using thermomechanical analysis , 1991 .

[24]  Saulius Juodkazis,et al.  Influence of ordering change on the optical and thermal properties of inflation polyethylene films , 2011 .

[25]  H. Pollock,et al.  Localised thermal analysis of a packaging film , 1999 .

[26]  B. Wunderlich,et al.  Mathematical description of differential scanning calorimetry based on periodic temperature modulation , 1994 .

[27]  M. Allmen.  Laser-beam interactions with materials , 1987 .

[28]  N. Sbirrazzuoli,et al.  Estimating the activation energy for non-isothermal crystallization of polymer melts , 2003 .

[29]  K. Vecchio,et al.  Influence of Molecular Conformation on the Constitutive Response of Polyethylene: A Comparison of HDPE, UHMWPE, and PEX , 2007 .

[30]  V. Velebný,et al.  An alternative DSC approach to study hydration of hyaluronan , 2010 .

[31]  G. Lazzara,et al.  Aqueous laponite clay dispersions in the presence of poly(ethylene oxide) or poly(propylene oxide) oligomers and their triblock copolymers. , 2008, The journal of physical chemistry. B.

[32]  M. Tuttle,et al.  The elastic and yield behavior of polyethylene tubes subjected to biaxial loadings , 1992 .

[33]  Koji Sugioka,et al.  Laser precision microfabrication , 2010 .

[34]  J. Suñol,et al.  Thermal analysis of aged hdpe based composites , 2002 .

[35]  A. Menyhárd,et al.  Crystallization of isotactic polypropylene in the presence of a β‐nucleating agent based on a trisamide of trimesic acid , 2011 .

[36]  R. Avolio,et al.  Isothermal and nonisothermal crystallization of HDPE composites containing multilayer carton scraps as filler , 2012 .