Study of the flexural behaviour and bonding strength of WC-Co metal matrix composite coatings produced by laser directed energy deposition

[1]  S. Siengchin.  A review on lightweight materials for defence applications: A present and future developments , 2023, Defence Technology.

[2]  Yang Wang,et al.  Surface modification technologies for enhancing the tribological properties of cemented carbides: A Review , 2023, Tribology International.

[3]  A. Lamikiz,et al.  Influence of process parameters on the particle-matrix interaction of WC-Co metal matrix composites produced by laser-directed energy deposition , 2022, Materials & Design.

[4]  Dehao Liu,et al.  Research on wear detection mechanism of cylinder liner-piston ring based on energy dissipation and AE , 2022, Wear.

[5]  J. Schoenung,et al.  Laser-based directed energy deposition (DED-LB) of advanced materials , 2022, Materials Science and Engineering: A.

[6]  Mehdi Shahedi Asl,et al.  Friction and Wear Properties of Short time heat-treated and laser surface re-melted NiCr-WC composite coatings at various dry sliding conditions , 2022, Journal of Materials Research and Technology.

[7]  E. Parsons,et al.  Additive manufacturing of aluminum metal matrix composites: Mechanical alloying of composite powders and single track consolidation with laser powder bed fusion , 2021, Additive Manufacturing.

[8]  Dongsheng Li,et al.  A review on the tooling technologies for composites manufacturing of aerospace structures: materials, structures and processes , 2021, Composites Part A: Applied Science and Manufacturing.

[9]  D. Verdi,et al.  Abrasive wear performance of laser cladded INCONEL 625 based metal matrix composites: Effect of the vanadium carbide reinforcement phase content , 2021, Surface and Coatings Technology.

[10]  Y. Lijun,et al.  Insights into microstructural evolution and dissolution characteristics of reinforced particles in tungsten carbide‑nickel composite coatings prepared by laser hot-wire deposition , 2021, International Journal of Refractory Metals and Hard Materials.

[11]  A. Zemlianov,et al.  Microstructure-based analysis of residual stress concentration and plastic strain localization followed by fracture in metal-matrix composites , 2021, Engineering Fracture Mechanics.

[12]  Lijun Yang,et al.  WC-Fe metal-matrix composite coatings fabricated by laser wire cladding , 2021, Journal of Materials Processing Technology.

[13]  Xionggang Lu,et al.  Microstructure and wear resistance of WC/Co-based coating on copper by plasma cladding , 2021 .

[14]  Hyoung Seop Kim,et al.  A perspective on precipitation-hardening high-entropy alloys fabricated by additive manufacturing , 2021, Materials & Design.

[15]  Siddhartha Roy,et al.  Review on development of metal/ceramic interpenetrating phase composites and critical analysis of their properties , 2021, Ceramics International.

[16]  P. Ikubanni,et al.  Synthesis, physico-mechanical and microstructural characterization of Al6063/SiC/PKSA hybrid reinforced composites , 2021, Scientific Reports.

[17]  Zhencai Zhu,et al.  Phase evolution and wear resistance of in-situ synthesized (Cr, W)23C6-WC composite ceramics reinforced Fe-based composite coatings produced by laser cladding , 2021 .

[18]  Paulraj Sathiya,et al.  Methods and materials for additive manufacturing: A critical review on advancements and challenges , 2021, Thin-Walled Structures.

[19]  S. Mohapatra,et al.  Wear: A Serious Problem in Industry , 2020 .

[20]  A. Nath,et al.  Development of process maps based on molten pool thermal history during laser cladding of Inconel 718/TiC metal matrix composite coatings , 2020 .

[21]  M. Barekat,et al.  Friction and wear behavior of laser cladded WC-Co and Ni/WC-Co deposits at high temperature , 2019, International Journal of Refractory Metals and Hard Materials.

[22]  Weidong Huang,et al.  Residual stress and distortion of rectangular and S-shaped Ti-6Al-4V parts by Directed Energy Deposition: Modelling and experimental calibration , 2019, Additive Manufacturing.

[23]  Guodong Zhang,et al.  Progress in additive manufacturing on new materials: A review , 2019, Journal of Materials Science & Technology.

[24]  Yingbin Hu,et al.  A review on laser deposition-additive manufacturing of ceramics and ceramic reinforced metal matrix composites , 2018, Ceramics International.

[25]  A. Kashani,et al.  Additive manufacturing (3D printing): A review of materials, methods, applications and challenges , 2018, Composites Part B: Engineering.

[26]  Ashish Kumar Nath,et al.  In-process detection of microstructural changes in laser cladding of in-situ Inconel 718/TiC metal matrix composite coating , 2018 .

[27]  Qunli Zhang,et al.  Solid-state fabrication of WCp-reinforced Stellite-6 composite coatings with supersonic laser deposition , 2017 .

[28]  Eric J. Faierson,et al.  A framework to link localized cooling and properties of directed energy deposition (DED)-processed Ti-6Al-4V , 2017 .

[29]  Ashish Kumar Nath,et al.  Online assessment of TiC decomposition in laser cladding of metal matrix composite coating , 2017 .

[30]  C. Ravindran,et al.  Comparison of Measurement Methods for Secondary Dendrite Arm Spacing , 2017, Metallography, Microstructure, and Analysis.

[31]  Liqun Li,et al.  Crack initiation and propagation behavior of WC particles reinforced Fe-based metal matrix composite produced by laser melting deposition , 2016 .

[32]  S. Zafar,et al.  Investigations on flexural performance and residual stresses in nanometric WC-12Co microwave clads , 2016 .

[33]  Adam Piasecki,et al.  Microstructure, microhardness and corrosion resistance of Stellite-6 coatings reinforced with WC particles using laser cladding , 2015 .

[34]  Rong Liu,et al.  Sliding wear and solid-particle erosion resistance of a novel high-tungsten Stellite alloy , 2015 .

[35]  Feng Yang,et al.  Influence of laser cladding process on the magnetic properties of WC–FeNiCr metal–matrix composite coatings , 2012 .

[36]  D. Gupta,et al.  On microstructure and flexural strength of metal–ceramic composite cladding developed through microwave heating , 2012 .

[37]  M. Shamanian,et al.  Microstructure and wear behavior of stellite 6 cladding on 17-4 PH stainless steel , 2011 .

[38]  C. Allibert,et al.  Solidification path and phase equilibria in the liquid-solid range of cobalt-base alloy , 1981 .