A comparative machinability analysis of polyimine vitrimer, epoxy and polycarbonate polymers through orthogonal machining experiments

[1]  J. P. Davim,et al.  A review on advanced cutting tools and technologies for edge trimming of carbon fibre reinforced polymer (CFRP) composites , 2023, Composites Part B: Engineering.

[2]  A. Israr,et al.  A novel optimization algorithm based PID controller design for real-time optimization of cutting depth and surface roughness in finish hard turning processes , 2023, Results in Engineering.

[3]  N. Geier,et al.  Analysis and modelling of thrust force in drilling of basalt and carbon fibre-reinforced polymer (BFRP and CFRP) composites , 2023, Journal of the Brazilian Society of Mechanical Sciences and Engineering.

[4]  P. Sántha,et al.  Potential applications of basalt fibre composites in thermal shielding , 2022, Journal of Thermal Analysis and Calorimetry.

[5]  C. Pereszlai,et al.  Delamination measurement in glass fibre reinforced polymer (GFRP) composite based on image differencing , 2022, Composites Part B: Engineering.

[6]  Shipeng Li,et al.  Surface quality evaluation for CFRP milling and its impact on the mechanical properties , 2022, The International Journal of Advanced Manufacturing Technology.

[7]  S. Ashworth,et al.  Effects of tool coating and tool wear on the surface quality and flexural strength of slotted CFRP , 2022, Wear.

[8]  C. Pereszlai,et al.  A drilling case study in polymer composites reinforced by virgin and recycled carbon fibres (CFRP and rCFRP) to analyse thrust force and torque , 2022, The International Journal of Advanced Manufacturing Technology.

[9]  C. Pereszlai,et al.  Drilling of recycled carbon fibre–reinforced polymer (rCFRP) composites: analysis of burrs and microstructure , 2022, The International Journal of Advanced Manufacturing Technology.

[10]  D. Huo,et al.  Machinability investigation of polymer/GNP nanocomposites in micro-milling , 2021, The International Journal of Advanced Manufacturing Technology.

[11]  N. Balc,et al.  Avoiding carbon fibre reinforced polymer delamination during abrasive water jet piercing: a new piercing method , 2021, The International Journal of Advanced Manufacturing Technology.

[12]  Islam Shyha,et al.  FE-simulation of machining processes of epoxy with Mulliken Boyce model , 2021, Journal of Manufacturing Processes.

[13]  M. Rani,et al.  A review on recycling and reuse methods for carbon fiber/glass fiber composites waste from wind turbine blades , 2021 .

[14]  Yu Huang,et al.  Precision cutting of epoxy resin board (ERB) by ultraviolet (UV) nanosecond laser ablation with consideration of hazardous gas protection , 2021 .

[15]  Kaifu Zhang,et al.  Investigation of high temperature effect on CFRP cutting mechanism based on a temperature controlled orthogonal cutting experiment , 2021, Composite Structures.

[16]  Ming Chen,et al.  Wear behavior of special tools in the drilling of CFRP composite laminates , 2021, Wear.

[17]  S. Rostam,et al.  Optimizing the simultaneous cutting-edge angles, included angle and nose radius for low cutting force in turning polyamide PA66 , 2020 .

[18]  C. Rudd,et al.  Recycled Carbon Fibers (rCF) in Automobiles: Towards Circular Economy , 2020, Materials Circular Economy.

[19]  Hui Wang,et al.  Delamination in rotary ultrasonic machining of CFRP composites: finite element analysis and experimental implementation , 2020 .

[20]  Nathan J. Van Zee,et al.  Vitrimers: Permanently crosslinked polymers with dynamic network topology , 2020, Progress in Polymer Science.

[21]  M. Miao,et al.  Recyclable thermoset hyperbranched polymers containing reversible hexahydro-s-triazine , 2019, Nature Sustainability.

[22]  J. Paulo Davim,et al.  Advanced cutting tools and technologies for drilling carbon fibre reinforced polymer (CFRP) composites: A review , 2019, Composites Part A: Applied Science and Manufacturing.

[23]  Yen Wei,et al.  Detecting topology freezing transition temperature of vitrimers by AIE luminogens , 2019, Nature Communications.

[24]  R. Vaziri,et al.  A study of energy dissipating mechanisms in orthogonal cutting of UD-CFRP composites , 2019, Composite Structures.

[25]  T. Czigány,et al.  Multifunctional application of carbon fiber reinforced polymer composites: Electrical properties of the reinforcing carbon fibers – A short review , 2019, Composites Part B: Engineering.

[26]  Zhenyuan Jia,et al.  Effects of cutting edge radius and fiber cutting angle on the cutting-induced surface damage in machining of unidirectional CFRP composite laminates , 2017 .

[27]  Kai Yu,et al.  Repairable Woven Carbon Fiber Composites with Full Recyclability Enabled by Malleable Polyimine Networks , 2016, Advanced materials.

[28]  L. Ye,et al.  On the toughness measurement for ductile polymers by orthogonal cutting , 2015 .

[29]  Kai Yu,et al.  Heat‐ or Water‐Driven Malleability in a Highly Recyclable Covalent Network Polymer , 2014, Advanced materials.

[30]  Ludwik Leibler,et al.  Silica-Like Malleable Materials from Permanent Organic Networks , 2011, Science.

[31]  Imtiaz Ahmed Choudhury,et al.  Plastics and their machining: A review , 1995 .

[32]  Andrea Toldy.  Challenges and opportunities of polymer recycling in the changing landscape of European legislation , 2023, Express Polymer Letters.

[33]  G. Szebényi.  High-performance composites and medical applications of polymers – the sunny side of the polymer industry , 2022, Express Polymer Letters.

[34]  R. Wertheim,et al.  Geometric empirical modelling of forces influenced by the cutting edge microgeometry in orthogonal cutting of unidirectional CFRP , 2021, Procedia CIRP.

[35]  Takashi Matsumura,et al.  Optimization in Milling of Polymer Materials for High Quality Surfaces , 2021, Int. J. Autom. Technol..

[36]  A. Toldy.  Recyclable-by-design thermoset polymers and composites , 2021, Express Polymer Letters.

[37]  M. Putz,et al.  Influence of cutting edge radius on process forces in orthogonal machining of carbon fibre reinforced plastics (CFRP) , 2019, Procedia CIRP.

[38]  Gregory K. Arbuckle,et al.  Experimental investigation and numerical simulation of burr formation in micro-milling of polycarbonates , 2019, Procedia Manufacturing.

[39]  Y. Mai,et al.  An experimental study of orthogonal cutting mechanisms for epoxies with two different crosslink densities , 2018 .

[40]  L. Salmén,et al.  Comparison of dynamic mechanical measurements and Tg determinations with two different instruments , 1994 .