The effects of process variables on pulsed Nd:YAG laser spot welds: Part II. AA 1100 aluminum and comparison to AISI 409 stainless steel

In this two-part article, the weldabilities of AA 1100 aluminum and AISI 409 stainless steel by the pulsed Nd:YAG laser welding process have been examined experimentally and compared. The effects of laser pulse time and power density on laser spot weld characteristics, such as weld diameter, penetration, melt area, melting ratio, porosity, and surface cratering, have been studied and explained qualitatively in relation to material-dependent variables such as absorptivity and thermophysical properties. The weldability of AISI 409 stainless steel was reported in Part I of this article. In the present article, the weldability of AA 1100 aluminum is reported and compared to that of AISI 409 stainless steel. Weld pool shapes in aluminum were found to be influenced by the mean power density of the laser beam and the laser pulse time. Both conduction-mode and keyhole-mode welding were observed in aluminum. Unlike stainless steel, however, drilling was not observed. Conduction-mode welds were produced in aluminum at power densities ranging from 3.2 to 10 GW/m2. The power density required for melting aluminum was approximately 4.5 times greater than stainless steel. The initial transient in weld pool development in aluminum occurred within 2 ms, and the aspect ratios (depth/width) of the steady-state conduction-mode weld pools were approximately 0.2. These values are about half those observed in stainless steel. The transition from conduction- to keyhole-mode welding occurred in aluminum at a power density of about 10 GW/m2, compared to about 4 GW/m2 for stainless steel. Weld defects such as porosity and cratering were observed in both aluminum and stainless steel spot welds. In both materials, there was an increased propensity for large occluded vapor pores near the root of keyhole-mode welds with increasing power density. In aluminum, pores were observed close to the fusion boundary. These could be eliminated by surface milling and vacuum annealing the specimens, suggesting that such pores were due to hydrogen. Finally, excellent agreement was obtained between experimental data from both alloys and an existing analytical model for conduction-mode laser spot welding. Two nondimensional parameters, the Fourier number and a nondimensional incident heat flux parameter, were derived and shown to completely characterize weld pool development in conduction-mode welds made in both materials.

[1]  W. W. Duley,et al.  Laser Material Interactions of Relevance To Metal Surface Treatment , 1986 .

[2]  W. Steen Laser Material Processing , 1991 .

[3]  Thomas Zacharia,et al.  Effect of evaporation and temperature-dependent material properties on weld pool development , 1991 .

[4]  S. Kou,et al.  Rapid melting and solidification of surface due to stationary heat flux , 1980 .

[5]  H. W. Kerr,et al.  Determining the Spot Size and Gaussian Distribution Coefficient of Pulsed Laser Beams Using KAPTON Films , 1993 .

[6]  C. J. Smithells,et al.  Smithells metals reference book , 1949 .

[7]  S. Kou Welding metallurgy and weldability of high strength aluminum alloys , 1986 .

[8]  T. DebRoy,et al.  Free surface flow and heat transfer in conduction mode laser welding , 1988 .

[9]  C. J Nonhof Material Processing with Nd Lasers , 1988 .

[10]  Energy-Beam redistribution and absorption in a drilling or welding cavity , 1992 .

[11]  P. W. Fuerschbach,et al.  On the weldability, composition, and hardness of pulsed and continuous Nd:YAG laser welds in aluminum alloys 6061,5456, and 5086 , 1988 .

[12]  H. W. Kerr,et al.  The effects of process variables on pulsed Nd:YAG laser spot welds: Part I. AISI 409 stainless steel , 1993 .

[13]  H. W. Kerr,et al.  Measuring the spatial intensity distribution of high-power focused laser beams using a rotating-wire type laser beam analyser. I: Theory , 1994 .

[14]  D. Olson,et al.  CHAPTER 3 - The Fundamentals of Weld Metal Pore Formation , 1990 .

[15]  N. Rykalin,et al.  Laser machining and welding , 1978 .

[16]  T. DebRoy,et al.  Heat transfer during Nd: Yag pulsed laser welding and its effect on solidification structure of austenitic stainless steels , 1989 .

[17]  Øystein Grong,et al.  Metallurgical modelling of welding , 1994 .

[18]  Stan A David,et al.  Trends in Welding Research , 1986 .

[19]  G. T. Martin,et al.  The temperature distribution in a semi-infinite body due to surface absorption of laser radiation , 1990 .