Predicting Maximum Acceptable Efforts for Repetitive Tasks

Objective: The objective was to develop an equation, for repetitive tasks, that uses frequency and/or duty cycle (DC) to predict maximum acceptable efforts (MAE) relative to maximum voluntary efforts (MVE). Background: Ergonomists must determine acceptable physical demands for a wide variety of tasks. Although a large database exists in the literature for maximum single-effort strength, far fewer repetitive tasks have psychophysical and/or physiological data available to guide the prediction of acceptable submaximal, repeated efforts. Method: DC represents the total effort duration divided by the cycle time. MAEs were calculated by dividing average psychophysics-based acceptable loads by corresponding single-effort maximum strength using 69 values from studies of the upper extremities. The author developed an equation to characterize the relationship between MAE and DC. Results: The resulting equation had DC taken to the exponent 0.24, and it predicted MAE very well (r2 = 0.87%, root mean square [RMS] difference = 7.2% of the maximum strength). At higher DC values, the equation also demonstrated good agreement with the published physiological data. Conclusion: The limited psychophysical database in the literature makes it difficult for ergonomists and engineers to recommend acceptable efforts for the large variety of repetitive tasks they evaluate. However, the proposed equation now allows for a correction of the large strength database to estimate acceptable force and torque limits for repetitive occupational tasks. Application: The proposed equation will have wide applications for ergonomic practitioners performing evaluations of repetitive tasks.

[1]  G. Hagg,et al.  Static work loads and occupational myalgia a new explanation model , 1991 .

[2]  C Fransson-Hall,et al.  Acceptability of Intermittent Handgrip Contractions Based on Physiological Response , 1994, Human factors.

[3]  G Sjøgaard,et al.  Intramuscular pressure, EMG and blood flow during low-level prolonged static contraction in man. , 1986, Acta physiologica Scandinavica.

[4]  Maury Nussbaum,et al.  Measurement and prediction of single and multi-digit finger strength , 2003, Ergonomics.

[5]  B Jonsson,et al.  Measurement and evaluation of local muscular strain in the shoulder during constrained work. , 1982, Journal of human ergology.

[6]  Jim Chiang,et al.  A psychophysical study to determine acceptable limits for repetitive hand impact severity during automotive trim installation , 2000 .

[7]  S H Snook,et al.  The design of manual handling tasks: revised tables of maximum acceptable weights and forces. , 1991, Ergonomics.

[8]  Jalaluddin B. Dahalan,et al.  Psychophysical frequency for a gripping task , 1993 .

[9]  Å. Kilbom,et al.  Repetitive work of the upper extremity: Part II — The scientific basis (knowledge base) for the guide , 1994 .

[10]  S H Snook,et al.  Psychophysical studies of repetitive wrist flexion and extension. , 1995, Ergonomics.

[11]  J G Chen,et al.  Advances in Industrial Engineering Applications and Practice , 1997 .

[12]  Richard Wells,et al.  Effect of cycle time and duty cycle on psychophysically determined acceptable levels in a highly repetitive task , 2005, Ergonomics.

[13]  S. S. Stevens.  On the psychophysical law. , 1957, Psychological review.

[14]  Stover H. Snook,et al.  Maximum acceptable forces for repetitive wrist extension with a pinch grip , 1999 .

[15]  R H Westgaard,et al.  Development of trapezius myalgia among female workers performing light manual work. , 1993, Scandinavian journal of work, environment & health.

[16]  David M. Andrews,et al.  Acceptable peak forces and impulses during manual hose insertions in the automobile industry , 2008 .

[17]  Jelena Stajic.  Filling in Gaps , 2011 .

[18]  Swei-Pi Wu,et al.  Effects of the adjustment period on psychophysically determined maximum acceptable weight of lift and the physiological cost , 2003 .

[19]  G. Hägg.  Human muscle fibre abnormalities related to occupational load , 2000, European Journal of Applied Physiology.

[20]  Ingvar Holmér.  Cold stress: Part II — The scientific basis (knowledge base) for the guide , 1994 .

[21]  K. Avin,et al.  Endurance time is joint-specific: A modelling and meta-analysis investigation , 2010, Ergonomics.

[22]  Allison Stephens,et al.  Maximal acceptable forces for manual insertions using a pulp pinch, oblique grasp and finger press , 2006 .

[23]  S H Snook,et al.  Psychophysical study of six hand movements , 2001, Ergonomics.

[24]  B Jonsson,et al.  Endurance limit of force in long-term intermittent static contractions. , 1977, Scandinavian journal of work, environment & health.

[25]  Beverley Norris,et al.  Filling 'gaps' in strength data for design. , 2003, Applied ergonomics.

[26]  Å. Kilbom,et al.  Physiological response in the forearm during and after isometric intermittent handgrip , 1991, European Journal of Applied Physiology and Occupational Physiology.

[27]  S H Snook,et al.  Maximum frequency of lift acceptable to male industrial workers. , 1968, American Industrial Hygiene Association journal.

[28]  Roland Kadefors,et al.  The role of muscle activity and mental load in the development of pain and degenerative processes at the muscle cell level during computer work , 2000, European Journal of Applied Physiology.

[29]  W Rohmert,et al.  Problems in determining rest allowances Part 1: use of modern methods to evaluate stress and strain in static muscular work. , 1973, Applied ergonomics.

[30]  M. Kramhøft,et al.  Reproducibility of goniometry of the wrist. , 1986, Scandinavian journal of rehabilitation medicine.

[31]  S H Snook.  Future directions of psychophysical studies. , 1999, Scandinavian journal of work, environment & health.

[32]  A. Mital,et al.  Human muscle strength definitions, measurement, and usage: Part I – Guidelines for the practitioner , 1998 .

[33]  A Aarås.  Postural load and the development of musculo-skeletal illness. , 1987, Scandinavian journal of rehabilitation medicine. Supplement.

[34]  Kurt Jørgensen,et al.  Electromyography and fatigue during prolonged, low-level static contractions , 2004, European Journal of Applied Physiology and Occupational Physiology.

[35]  A Garg,et al.  Revised NIOSH equation for the design and evaluation of manual lifting tasks. , 1993, Ergonomics.

[36]  Waldemar Karwowski,et al.  Manual Materials Handling , 1990 .

[37]  Snook Sh,et al.  Future directions of psychophysical studies. , 1999 .

[38]  Milad G. Ishac,et al.  Predicting Distal Arm Demand from Task Requirements , 2007 .

[39]  Waldemar Karwowski,et al.  The occupational ergonomics handbook , 2006 .

[40]  Richard Wells,et al.  Measurement of prehensile grasp capabilities by a force and moment wrench: Methodological development and assessment of manual workers , 2004, Ergonomics.

[41]  K. Hansen,et al.  Trapezius muscle load as a risk indicator for occupational shoulder-neck complaints , 1993, International archives of occupational and environmental health.

[42]  R H Westgaard,et al.  Pattern of muscle activity during stereotyped work and its relation to muscle pain , 1990, International archives of occupational and environmental health.

[43]  B. Jensen,et al.  Low-Level Static Exertions , 2003 .

[44]  S H Snook,et al.  Maximum acceptable forces for repetitive ulnar deviation of the wrist. , 1997, American Industrial Hygiene Association journal.

[45]  Vincent M Ciriello,et al.  Maximal acceptable torques of highly repetitive screw driving, ulnar deviation, and handgrip tasks for 7-hour workdays. , 2002, AIHA journal : a journal for the science of occupational and environmental health and safety.

[46]  Sang D. Choi,et al.  The effect of adjustment period on maximum acceptable frequency for a roofing task , 2007 .