Mechanical properties of 3D printed polylactic acid elements: Experimental and numerical insights

[1]  Sonia Marfia,et al.  Multiscale technique for the analysis of 3D-printed materials , 2021 .

[2]  A. Ragauskas,et al.  Critical review of FDM 3D printing of PLA biocomposites filled with biomass resources, characterization, biodegradability, upcycling and opportunities for biorefineries , 2021 .

[3]  S. Marfia,et al.  Computational homogenization of 3D printed materials by a reduced order model , 2021 .

[4]  W. Boyes,et al.  3D Printer Particle Emissions: Translation to Internal Dose in Adults and Children. , 2021, Journal of aerosol science.

[5]  Yanan Wang,et al.  An accurate finite element approach for programming 4D-printed self-morphing structures produced by fused deposition modeling , 2020 .

[6]  Tianyu Yu,et al.  Repetitive recycling of 3D printing PLA filament as renewable resources on mechanical and thermal loads , 2020 .

[7]  Li Yang,et al.  Introduction to Additive Manufacturing , 2020, Additive Manufacturing.

[8]  I. Fidan,et al.  Prediction of mechanical properties of fused filament fabricated structures via asymptotic homogenization , 2020, Mechanics of Materials.

[9]  H. Ouyang,et al.  Tensile failure strength and separation angle of FDM 3D printing PLA material: Experimental and theoretical analyses , 2020 .

[10]  I. Buj-Corral,et al.  Elastic Asymmetry of PLA Material in FDM-Printed Parts: Considerations Concerning Experimental Characterisation for Use in Numerical Simulations , 2019, Materials.

[11]  Yuansong Chen,et al.  Novel mechanical models of tensile strength and elastic property of FDM AM PLA materials: Experimental and theoretical analyses , 2019, Materials & Design.

[12]  Huamin Zhou,et al.  Improved design of fused deposition modeling equipment for 3D printing of high-performance PEEK parts , 2019, Mechanics of Materials.

[13]  S. Mirkhalaf,et al.  The mechanical behavior of polylactic acid (PLA) films: fabrication, experiments and modelling , 2019, Mechanics of Time-Dependent Materials.

[14]  C. V. Singh,et al.  Analysis of the Material Behavior of 3D Printed Laminates Via FFF , 2019, Experimental Mechanics.

[15]  Harshit K. Dave,et al.  Flexural strength of fused filament fabricated (FFF) PLA parts on an open-source 3D printer , 2018, Advances in Manufacturing.

[16]  Tingting Huang,et al.  Ultimate Tensile Strength in Fused Deposition Modeling Considering Process Parameters of Flow Rate and Printing Head Speed , 2018, 2018 12th International Conference on Reliability, Maintainability, and Safety (ICRMS).

[17]  C. V. Singh,et al.  Development of constitutive material model of 3D printed structure via FDM , 2018 .

[18]  A. Ma,et al.  The microstructure and mechanical properties of 3D printed carbon nanotube‐polylactic acid composites , 2018 .

[19]  Sonia Marfia,et al.  Multiscale technique for nonlinear analysis of elastoplastic and viscoplastic composites , 2018 .

[20]  R. Maskeliūnas,et al.  Multi-scale finite element modeling of 3D printed structures subjected to mechanical loads , 2017 .

[21]  Yong Li,et al.  Measurements of the mechanical response of unidirectional 3D-printed PLA , 2017 .

[22]  R. Luciano,et al.  Multiscale failure analysis of periodic masonry structures with traditional and fiber-reinforced mortar joints , 2017 .

[23]  Peter Ifju,et al.  Experimental characterization of the mechanical properties of 3D-printed ABS and polycarbonate parts , 2017 .

[24]  Joshua M. Pearce,et al.  Tensile strength of commercial polymer materials for fused filament fabrication 3D printing , 2017 .

[25]  Sonia Marfia,et al.  Homogenization of elastic–viscoplastic composites by the Mixed TFA , 2017 .

[26]  Ferdinando Auricchio,et al.  Influence of meso-structure and chemical composition on FDM 3D-printed parts , 2017 .

[27]  Garrett W. Melenka,et al.  Evaluation and prediction of the tensile properties of continuous fiber-reinforced 3D printed structures , 2016 .

[28]  Ping Hu,et al.  Isotropic and anisotropic elasticity and yielding of 3D printed material , 2016 .

[29]  Todd Letcher,et al.  Failure Analysis and Mechanical Characterization of 3D Printed ABS With Respect to Layer Thickness and Orientation , 2016, Journal of Failure Analysis and Prevention.

[30]  Caterina Casavola,et al.  Orthotropic mechanical properties of fused deposition modelling parts described by classical laminate theory , 2016 .

[31]  Somnath Ghosh,et al.  Adaptive concurrent multi-level model for multi-scale analysis of ductile fracture in heterogeneous aluminum alloys , 2013 .

[32]  Sonia Marfia,et al.  Analysis of SMA composite laminates using a multiscale modelling technique , 2007 .

[33]  John E. Renaud,et al.  Mechanical behavior of acrylonitrile butadiene styrene fused deposition materials modeling , 2003 .

[34]  P. Wright,et al.  Anisotropic material properties of fused deposition modeling ABS , 2002 .

[35]  Alberto Taliercio,et al.  A micromechanical model for the analysis of unidirectional elastoplastic composites subjected to 3d stresses , 1999 .

[36]  Elio Sacco,et al.  Variational methods for the homogenization of periodic heterogeneous media , 1998 .

[37]  R. Hill.  A theory of the yielding and plastic flow of anisotropic metals , 1948, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.