Reinforcement effects of MWCNT and VGCF in bulk composites and interlayer of CFRP laminates

Abstract The reinforcement effects of two nanofillers, i.e., multi-walled carbon nanotube (MWCNT) and vapor grown carbon fiber (VGCF), which are used at the interface of conventional CFRP laminates, and in epoxy bulk composites, have been investigated. When using the two nanofillers at the interface between two conventional CFRP sublaminates, the Mode-I interlaminar tensile strength and fracture toughness of CFRP laminates are improved significantly. The performance of VGCF is better than that of MWCNT in this case. For epoxy bulk composites, the two nanofillers play a similar role of good reinforcement in Young’s modulus and tensile strength. However, the Mode-I fracture toughness of epoxy/MWCNT is much better than that of epoxy/VGCF.

[1]  Ning Hu,et al.  Stable numerical simulations of propagations of complex damages in composite structures under transverse loads , 2007 .

[2]  Linda S. Schadler,et al.  LOAD TRANSFER IN CARBON NANOTUBE EPOXY COMPOSITES , 1998 .

[3]  A. Kelly,et al.  Tensile properties of fibre-reinforced metals: Copper/tungsten and copper/molybdenum , 1965 .

[4]  H. L. Cox.  The elasticity and strength of paper and other fibrous materials , 1952 .

[5]  Sung-Moo Song,et al.  Mechanical and physical properties of epoxy composites reinforced by vapor grown carbon nanofibers , 2005 .

[6]  Hiroshi Fukuda,et al.  A probabilistic theory of the strength of short-fibre composites with variable fibre length and orientation , 1982 .

[7]  M. Pitkethly,et al.  Characterizing the fibre/matrix interface of carbon fibre-reinforced composites using a single fibre pull-out test , 1990 .

[8]  Meng-Kao Yeh,et al.  Fabrication and mechanical properties of multi-walled carbon nanotubes/epoxy nanocomposites , 2008 .

[9]  Y. M. Wang,et al.  Direct Mechanical Measurement of the Tensile Strength and Elastic Modulus of Multiwalled Carbon Nanotubes , 2006, Microscopy and Microanalysis.

[10]  J. Bai,et al.  Effect of the length and the aggregate size of MWNTs on the improvement efficiency of the mechanical and electrical properties of nanocomposites—experimental investigation , 2003 .

[11]  Ning Hu,et al.  A 3D brick element based on Hu–Washizu variational principle for mesh distortion , 2002 .

[12]  Masahiro Arai,et al.  Mode I and mode II interlaminar fracture toughness of CFRP laminates toughened by carbon nanofiber interlayer , 2008 .

[13]  S. Bonnamy,et al.  Functionalization of multiwall carbon nanotubes: Properties of nanotubes-epoxy composites , 2002 .

[14]  François Béguin,et al.  Mechanical properties of multiwall carbon nanotubes/epoxy composites: influence of network morphology , 2004 .

[15]  Rikio Yokota,et al.  Characterization of multi-walled carbon nanotube/phenylethynyl terminated polyimide composites , 2004 .

[16]  Tomohiro Yokozeki,et al.  Mechanical properties of CFRP laminates manufactured from unidirectional prepregs using CSCNT-dispersed epoxy , 2007 .

[17]  W. DiNatale,et al.  Generation and detection of coherent terahertz waves using two photomixers , 1998 .