Steady-state modeling and bifurcation behavior of circulating fluidized bed membrane reformer¿regenerator for the production of hydrogen for fuel cells from heptane

The production of hydrogen for fuel cells by steam reforming of heptane is investigated in a Circulating Fluidized Bed Membrane Reformer-Regenerator (CFBMRR) system (A.I.Ch.E. Journal 49(5) (2003) 1250). Palladium based hydrogen permselective membranes are used for hydrogen removal and dense perovskite oxygen permselective membranes are used for oxygen introduction. A series of pseudo-steady-state simulations show that when the catalyst is not regenerated, the circulating nickel reforming catalyst deactivates quickly and the “half catalyst activity life” for efficient production of hydrogen is quite short, especially at high temperatures. Efficient continuous catalyst regeneration can keep the catalyst activity high (∼1.0). With continuous catalyst regeneration, autothermal operation for the entire adiabatic reformer–regenerator system is achievable when the exothermic heat generated from the catalyst regenerator is sufficient to compensate for the endothermic heat consumed in the riser reformer. This type of autothermal operation becomes less likely at high steam to carbon feed ratios. This is due to the fact that carbon deposition rate decreases leading to the decrease of autothermal circulating feed temperature and energy-based hydrogen yield (adiabatic hydrogen yield in autothermal reformer–regenerator system). Multiplicity of the steady states for the reformer is possible for this configuration. With the steam to carbon feed ratio as the bifurcation parameter, multiplicity occurs between the two bifurcation points 1.444 and 2.251 mol/mol. In this multiplicity region, the energy-based hydrogen yield at the upper steady state with high regenerator output temperature is surprisingly the lowest one. While it is the highest one at the lower steady state with low regenerator output temperature. The maximum energy-based hydrogen yield is about 15.58 moles of hydrogen per mole of heptane fed at the lower steady-state when steam to carbon feed ratio is very close to the bifurcation value of 1.444 mol/mol. After removing the sweep gas steam by downstream cooling and de-humidification, the product hydrogen from steam reforming of hydrocarbons can be used for fuel cells with high purity (∼100%).

[1]  L. F. Brown.  A comparative study of fuels for on-board hydrogen production for fuel-cell-powered automobiles , 2001 .

[2]  Dan Luss,et al.  Ceramic membrane reactor for synthesis gas production , 2001 .

[3]  G. Froment,et al.  Methane steam reforming, methanation and water‐gas shift: I. Intrinsic kinetics , 1989 .

[4]  Said S.E.H. Elnashaie,et al.  Simulation and optimization of an industrial ammonia reactor , 1988 .

[5]  P. B. Tottrup,et al.  Kinetics of decomposition of carbon monoxide on a supported nickel catalyst. [Effects of temperature, water, and hydrogen; competition for methanation] , 1976 .

[6]  J. Rostrup-Nielsen.  Coking on nickel catalysts for steam reforming of hydrocarbons , 1974 .

[7]  Thomas Sandahl Christensen,et al.  Adiabatic prereforming of hydrocarbons — an important step in syngas production , 1996 .

[8]  Bernard P. A. Grandjean,et al.  Methane steam reforming in asymmetric Pd- and Pd-Ag/porous SS membrane reactors , 1994 .

[9]  Octave Levenspiel,et al.  Entrainment of solids from fluidized beds I. Hold-up of solids in the freeboard II. Operation of fast fluidized beds , 1990 .

[10]  Christopher E. Borroni-Bird,et al.  Fuel cell commercialization issues for light-duty vehicle applications , 1996 .

[11]  Said S.E.H. Elnashaie,et al.  Modelling, Simulation and Optimization of Industrial Fixed Bed Catalytic Reactors , 1994 .

[12]  Gilbert F. Froment,et al.  Kinetic Study of the Carbon Filament Formation by Methane Cracking on a Nickel Catalyst , 1997 .

[13]  John R. Grace,et al.  The fluidized-bed membrane reactor for steam methane reforming: model verification and parametric study , 1997 .

[14]  Caixia Chen,et al.  Numerical simulation of entrained flow coal gasifiers. Part I: modeling of coal gasification in an entrained flow gasifier , 2000 .

[15]  S. W. Ing.  Entrainment of solids from fluidized beds , 1953 .

[16]  Jamal Chaouki,et al.  Scaling considerations for circulating fluidized bed risers , 1992 .

[17]  Said S.E.H. Elnashaie,et al.  THE COUPLING OF CATALYTIC STEAM REFORMING AND OXIDATIVE REFORMING OF METHANE TO PRODUCE PURE HYDROGEN IN A NOVEL CIRCULATING FAST FLUIDIZATION BED MEMBRANE REFORMER , 2002 .

[18]  Said S.E.H. Elnashaie,et al.  A fluidized bed membrane reactor for the steam reforming of methane , 1991 .

[19]  R. E. Stoll,et al.  Hydrogen : what are the costs? : Plant utilities , 2000 .

[20]  C. Tsai.  Dense perovskite membrane reactors for partial oxidation of methane to syngas , 1997 .

[21]  E. Kreyszig,et al.  Advanced Engineering Mathematics. , 1974 .

[22]  Octave Levenspiel,et al.  Circulating fluidized-bed reactors , 1997 .

[23]  John R. Grace,et al.  The fluidized bed membrane reactor system: a pilot scale experimental study , 1994 .

[24]  T. Nejat Veziroglu,et al.  A step on the road to Hydrogen Civilization , 2002 .

[25]  Said S.E.H. Elnashaie,et al.  Modeling and optimization of a novel membrane reformer for higher hydrocarbons , 2003 .

[26]  A. M. Adris,et al.  Fluidized-bed steam methane reforming with oxygen input , 1999 .

[27]  Peter B. Tøttrup,et al.  Evaluation of intrinsic steam reforming kinetic parameters from rate measurements on full particle size , 1982 .

[28]  Wanqin Jin,et al.  Experimental and simulation study on a catalyst packed tubular dense membrane reactor for partial oxidation of methane to syngas , 2000 .