Design and cold flow test of a scramjet nozzle with nonuniform inflow

Abstract Dramatic differences in lift and pitching moment of a scramjet nozzle are inevitably produced when its inlet is nonuniform. A rotational method of characteristics computer program which takes into account the non-uniform inflow effects has been developed for designing asymmetric scramjet nozzles. Typical design cases with a given non-uniform Mach number profile and the corresponding mass-weighted average uniform Mach number profile were developed. Then, three-dimensional computational fluid dynamics analyses and cold flow experimental measurements were conducted to quantify performance improvement of the nozzle with the non-uniform design. Both the computation and experiment results indicate that the nozzle design with the non-uniform Mach number profile always exhibit better performance than the design with the uniform Mach number profile, particularly for lift and pitching moment. Compared with the nozzle design with uniform inflow, the improvement of axial thrust coefficient in the nozzle design with non-uniform inflow is approximately 1.75% at the design point, with a nozzle pressure ratio of 35. Moreover, the benefits on lift and pitching moment coefficients of the nozzle design with non-uniform inflow are approximately 6.51% and 6.35% at the design point, respectively. These results confirm that considering non-uniform distribution of the entrance flow parameters of a scramjet nozzle is necessary.

[1]  Seung-Ho Lee,et al.  Single expansion ramp nozzle simulations , 1992 .

[2]  Suresh Menon,et al.  Large Eddy Simulation of Scramjet Combustion Using a Subgrid Mixing/combustion Model , 2003 .

[3]  Theo G. Keith,et al.  Analysis and design of optimized truncated scarfed nozzles subject to external flow effects , 1990 .

[4]  Sean M. Torrez,et al.  Rapid Analysis of Scramjet and Linear Plug Nozzles , 2012 .

[5]  William H. Heiser,et al.  Hypersonic Airbreathing Propulsion , 1994 .

[6]  Leon Schindel.  Effect of Nommiform Nozzle Flow on Scramjet Performance , 1999 .

[7]  R. Cummings,et al.  Fifty years of hypersonics: where we've been, where we're going , 2003 .

[8]  Sandra L. Snelling.  Effect of Nonuniform Entrance Flow Profile on Hypersonic Nozzle Pitching Moment , 1991 .

[9]  E. H. Andrews,et al.  Review of NASA's Hypersonic Research Engine Project , 1993 .

[10]  Corin Segal,et al.  The Scramjet Engine: Processes and Characteristics , 2009 .

[11]  Anatole P. Kurkov,et al.  An Analytical and Experimental Study of Supersonic Combustion of Hydrogen in Vitiated Air Stream , 1973 .

[12]  Richard L. Gaffney.  Erratum on Design of a Pulse-Facility Nozzle Using the Rotational Method Of Characteristics , 2007 .

[13]  Ronald S. Fry,et al.  A Century of Ramjet Propulsion Technology Evolution , 2004 .

[14]  J. Anderson,et al.  Modern Compressible Flow: With Historical Perspective , 1982 .

[15]  Lin Ma,et al.  Design exploration for a single expansion ramp nozzle (SERN) using data mining , 2013 .

[16]  R. Mercier,et al.  Hypersonic Technology (HyTech) Program overview , 1998 .

[17]  A. Gülhan,et al.  Infrared Thermography and Pitot Pressure Measurements of a Scramjet Nozzle Flowfield , 2009 .

[18]  Nicholas A. Cumpsty,et al.  Averaging Nonuniform Flow for a Purpose , 2006 .

[19]  Richard L. Gaffney,et al.  Design of a Pulse-Facility Nozzle Using the Rotational Method of Characteristics , 2006 .

[20]  P. Bradshaw,et al.  Physical and Computational Aspects of Convective Heat Transfer , 1984 .

[21]  Reiner Decher.  Nonuniform Flow Through Nozzles , 1978 .

[22]  Russell R. Boyce,et al.  Nozzle design optimization for axisymmetric scramjets by using surrogate-assisted evolutionary algorithms , 2012 .

[23]  Ulrich Henne,et al.  Measurement of Flow Properties and Thrust on Scramjet Nozzle Using Pressure-Sensitive Paint , 2009 .

[24]  Houshang Ebrahimi,et al.  Numerical study of phenomena affecting the prediction of scramjet combustor and nozzle performance , 1993 .