Friction torque in rolling bearings lubricated with axle gear oils

Abstract As a part of the main research project within the aim of increasing significantly drive axle efficiency, this work focuses on rolling bearing friction torque lubricated with five fully formulated axle gear oils with different viscosity and different formulations. The lubricant tribological behaviour in different rolling bearings was analyzed. A modified Four-Ball Machine was used to test the rolling bearings. The effect of speed, temperature and axial load on rolling bearing friction torque was assessed. Experimental results for the internal friction torque were validated with an SKF model. Direct comparisons in terms of friction torque between axle gear oils when they are lubricating different rolling bearing types are presented and discussed.

[1]  Ramiro C. Martins,et al.  Gearbox power loss. Part I: Losses in rolling bearings , 2015 .

[2]  Bernd-Robert Höhn,et al.  Influence factors on gearbox power loss , 2011 .

[3]  Ahmet Kahraman,et al.  Prediction of friction-related power losses of hypoid gear pairs , 2007 .

[4]  Robert R. Binoniemi,et al.  Seal Friction Effect on Drive Axle Efficiency , 2005 .

[5]  Mohamed Haddar,et al.  Axle gear oils: Tribological characterization under full film lubrication , 2017 .

[6]  Johannes Brändlein,et al.  Ball and roller bearings: Theory, design, and application , 1985 .

[7]  Jorge H.O. Seabra,et al.  Experimental measuring procedure for the friction torque in rolling bearings , 2010 .

[8]  Hugh Spikes,et al.  The Measurement and Study of Very Thin Lubricant Films in Concentrated Contacts , 1991 .

[9]  Sheng Li,et al.  Prediction of mechanical gear mesh efficiency of hypoid gear pairs , 2010 .

[10]  Andrew V. Olver,et al.  The efficiency of a hypoid axle—a thermally coupled lubrication model , 2013 .

[11]  Kiyohiko Umezawa,et al.  EXACT MEASUREMENT OF POWER LOSS IN AUTOMOTIVE TRANSMISSION AND AXLE FOR FUEL ECONOMY , 1983 .

[12]  Sheng Li,et al.  Development and Validation of an Automotive Axle Power Loss Model , 2016 .

[13]  Ramiro C. Martins,et al.  Friction torque of thrust ball bearings lubricated with wind turbine gear oils , 2013 .

[14]  B. Hamrock.  Ball bearing lubrication , 1981 .

[15]  Joshua Hurley.  AN EXPERIMENTAL INVESTIGATION OF THERMAL BEHAVIOR OF AN AUTOMOTIVE REAR AXLE , 2009 .

[16]  Jörg Loos,et al.  Viscosity-pressure-temperature behaviour of mineral oil and synthetic oils , 2001 .

[17]  Teik C. Lim,et al.  VIBRATION ANALYSIS OF HYPOID TRANSMISSIONS APPLYING AN EXACT GEOMETRY-BASED GEAR MESH THEORY , 2001 .

[18]  Teik C. Lim,et al.  Dynamics of Hypoid Gear Transmission With Nonlinear Time-Varying Mesh Characteristics , 2003 .

[19]  Avinash Singh,et al.  Effects of Bearing Preload, Oil Volume, and Operating Temperature on Axle Power Losses , 2012 .

[21]  Christophe Changenet,et al.  Housing Influence on Churning Losses in Geared Transmissions , 2008 .

[22]  Yoshiyuki Ko,et al.  Measurements of Power Losses in Automobile Drive Train , 1984 .

[24]  V. Bala,et al.  Fuel economy of multigrade gear lubricants , 2000 .

[25]  M. Haddar,et al.  Axle gear oils: Friction, wear and tribofilm generation under boundary lubrication regime , 2017 .

[26]  Anant Shivaji Kolekar.  Lubrication & efficiency of rear wheel drive axles in road vehicles , 2013 .

[27]  Douglas C. Porrett,et al.  Development of a Laboratory Axle Efficiency Test , 1980 .

[28]  Bernd-Robert Höhn,et al.  Optimization of Gearbox Efficiency , 2009 .

[29]  D. Dowson,et al.  A Numerical Solution to the Elasto-Hydrodynamic Problem , 1959 .

[30]  Franz Joachim,et al.  Reduction of Power Losses in Transmissions and Gearings , 2011 .

[31]  Simon D. Evans.  Delivering Axle Efficiency and Fuel Economy Through Optimised Fluid Design , 2014 .

[32]  Hugh Spikes,et al.  Lubricant Film Thickness in Rough Surface, Mixed Elastohydrodynamic Contact , 2000 .

[33]  Teik C. Lim,et al.  Dynamics of a hypoid gear pair considering the effects of time-varying mesh parameters and backlash nonlinearity , 2007 .

[35]  Georg von Petery.  Fuel economy by custom-made: Bearings for differentials from BMW , 2004 .

[36]  Kay K. Bjornen,et al.  Development of a Fuel Efficient Multipurpose 75W-90 Gear Lubricant , 2003 .

[37]  V. Bala,et al.  Rheological Properties Affecting the Fuel Economy of Multigrade Automotive Gear Lubricants , 2000 .