The aerodynamic loading of radial and mixed-flow turbines

Abstract In this paper we investigate the possibility of correlating the aerodynamic loading of radial and mixed-flow turbines in some systematic manner, as is widely done and recognized for axial stages. The loading is shown to be closely related to incidence, and an optimum incidence angle is often calculated from the rotor blade number using centrifugal compressor correlations. It is found that there are many examples of high-efficiency stages which have far fewer blades than these correlations suggest. The relation between blade loading, flow coefficient and isentropic efficiency is investigated in the results of tests on some 40 different turbine stages, and a good correlation is found to exist, with a clearly defined region of best efficiency on a map of loading vs flow coefficients. Various lift and drag coefficients are also defined and calculated for a number of tested turbines, but in general these parameters correlate the data less satisfactorily than the blade loading and flow coefficients. The lift-drag ratio is, however, a useful parameter for optimizing highly loaded stage designs.

[1]  M. G. Kofskey,et al.  Cold performance evaluation of a 6.02-inch radial inflow turbine designed for a 10-kilowatt shaft output Brayton cycle space power generation system , 1966 .

[2]  N. C. Baines,et al.  Design of a Highly Loaded Mixed Flow Turbine , 1992 .

[3]  S. F. Smith.  A Simple Correlation of Turbine Efficiency , 1965, The Journal of the Royal Aeronautical Society.

[4]  J. E. Haas,et al.  Experimental performance and analysis of 15.04-centimeter-tip-diameter, radial-inflow turbine with work factor of 1.126 and thick blading , 1980 .

[5]  W. J. Nusbaum,et al.  Experimental performance evaluation of a 4.59- inch radial-inflow turbine over a range of Reynolds number , 1967 .

[6]  S. M. Futral,et al.  Experimental results of varying the blade- shroud clearance in a 6.02-inch radial-inflow turbine , 1970 .

[7]  M. G. Kofskey,et al.  Cold performance evaluation of 4.97-inch radial-inflow turbine design for single-shaft Brayton cycle space-power system , 1969 .

[8]  M. G. Kofskey,et al.  Cold performance evaluation of a 4.59-inch radial-inflow turbine designed for a Brayton- cycle space power system , 1966 .

[9]  S. T. Kitson.  Aerodynamic investigation of radial turbines using computational methods , 1992 .

[10]  N. C. Baines,et al.  The Effects of Blade Loading in Radial and Mixed Flow Turbines , 1992 .

[11]  S. M. Futral,et al.  Experimental performance evaluation of a 6.02-inch radial-inflow turbine over a range of Reynolds number , 1967 .

[12]  M. G. Kofskey,et al.  Experimental evaluation of a 3.50-inch radial turbine designed for a 10-kilowatt space power system , 1969 .

[13]  Ichiro Watanabe,et al.  Effect of Dimensional Parameters of Impellers on Performance Characteristics of a Radial-Inflow Turbine , 1971 .

[14]  Keith Robert Pullen,et al.  The Design and Evaluation of a High Pressure Ratio Radial Turbine , 1992 .

[15]  A. J. Glassman,et al.  FORTRAN program for predicting off-design performance of radial-inflow turbines , 1975 .

[16]  C. Rodgers,et al.  Performance of a High-Efficiency Radial/Axial Turbine , 1987 .

[17]  M. G. Kofskey,et al.  Effects of specific speed on the experimental performance of a radial-inflow turbine , 1971 .